EasyManuals Logo

Harvia M3 SL User Manual

Harvia M3 SL
16 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
EN DE
9
3. SAUNA ROOM
Figure 3. Ventilation of the Sauna Room
Abbildung 3. Belüftung der Saunakabine
3.1. Effects that Heating the Stove has on
the Sauna Room
Light-coloured floor materials will become dirty from
the ash, particles of stone and metal flakes that fall
from the stove. Use floor coverings made of dark
materials and dark joint grouts.
It is perfectly normal for the wooden surfaces of
the sauna room to blacken in time. The blackening
may be accelerated by
 sunlight
 heat from the stove
 protective agents on the walls (protective
agents have a poor heat resistance level)
 fine particles disintegrating from the sauna
stones which rise with the air flow
 smoke that enters the sauna, for example,
when adding firewood.
When installation instructions given by the
manufacturer are followed, the stove will not
heat the inflammable material in sauna room to a
dangerous level.
3.2. Ventilation of the Sauna Room
See figure 3.
A. Supply air vent location. If mechanical exhaust
ventilation is used, place the supply air vent
above the stove. If gravity exhaust ventilation
is used, place the supply air vent below or next
to the stove. The diameter of the supply air
pipe must be 50–100 mm.
B. Exhaust air vent. Place the exhaust air vent
near the floor, as far away from the stove as
possible. The diameter of the exhaust air pipe
should be twice the diameter of the supply air
pipe.
C. Make sure there is enough air to compensate.
3.3. Sauna Room Hygiene
Bench towels should be used during bathing to
prevent sweat from getting onto the benches.
The benches, walls and floor of the sauna should
be washed thoroughly at least every six months.
Use a scrubbing brush and sauna detergent.
3. SAUNAKABINE
3.1. Aufheizen der Saunakabine
Helle Böden werden durch Asche, Steinpartikel und
aus dem Ofen fallende Metallsplitter verunreinigt.
Verwenden Sie Bodenabdeckungen aus dunklen Ma-
terialien und dunkle Zementschlämme.
Es ist ganz normal, wenn sich die Holzoberflächen
einer Sauna mit der Zeit verfärben. Die Schwärzung
wird beschleunigt durch:
 Sonnenlicht
 Hitze des Ofens
 Täfelungsschutz an den Wänden (mit geringem
Hitzewiderstand)
 Feinpartikel, die aus den zerfallenden Sauna-
steinen in die Luft entweichen
 Rauch, der in die Sauna kommt, zum Beispiel
beim Nachlegen von Brennholz.
Wenn die vom Hersteller gegebenen Montage-
anweisungen befolgt werden, erwärmt der Ofen
brennbare Materialien in der Saunakabine auf keine
gefährliche Temperaturen.
3.2. Belüftung der Saunakabine
Siehe Abbildung 3.
A. Luftzufuhr. Bei mechanischer Entlüftung Luft-
zufuhr über dem Ofen anbringen. Bei Schwer-
kraftentlüftung Luftzufuhr unter oder neben
dem Ofen anbringen. Der Durchmesser des
Luftzufuhrrohres muss 50–100 mm betragen.
B. Entlüftung. Entlüftung in Bodennähe anbringen,
so weit weg vom Ofen wie möglich. Der Durch-
messer des Entlüftungsrohres sollte doppelt so
groß sein wie bei der Luftzufuhr.
C. Sorgen Sie im Ausgleich für genügend Luft.
3.3. Hygiene der Saunakabine
Liegetücher benutzen, um die Bänke vor Schweiß
zu schützen.
Bänke, Wände und Boden der Sauna mindestens
alle sechs Monate waschen. Bürste und Saunarei-
nigungsmittel verwenden.
A
A
B
C

Table of Contents

Other manuals for Harvia M3 SL

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Harvia M3 SL and is the answer not in the manual?

Harvia M3 SL Specifications

General IconGeneral
BrandHarvia
ModelM3 SL
CategoryStove
LanguageEnglish

Related product manuals