Haussmann Xpert DS1800 User Manual (English)

Questions and Answers:

A
Ashley HillAug 11, 2025
What to do if my Haussmann Xpert DS1800 motor stalls and blows fuses?
- D
  Dylan BryantAug 11, 2025
  If the Haussmann Xpert Sander motor stalls, causing blown fuses or tripped circuit breakers, it could be due to several reasons: * The motor is overloaded because too much material is being removed per pass. * There's a short circuit in the motor or loose connections. * The voltage is too low. * Incorrect fuses or circuit breakers are installed. To resolve this: 1. Reduce the amount of material removed per pass by adjusting the drum height. 2. Inspect the motor connections for loose or shorted terminals, or worn wire insulation. 3. Correct the low line voltage conditions. 4. Install the correct fuses or circuit breakers.
R
Ruth MillerAug 17, 2025
What to do if Haussmann Xpert Sander motor won't start and fuses are blown?
- C
  Cathy BatesAug 18, 2025
  If the Haussmann Xpert Sander motor won't start and the fuses are blown or circuit breakers are tripped, it could be due to: * A short circuit in the line cord or plug. * A short circuit in the motor or loose connections. * Incorrect fuses or circuit breakers in the power line. * The thermal overload protector has activated. To fix this: 1. Inspect the line cord or plug for damaged insulation and shorted wires. 2. Inspect all lead connections on the motor for loose or shorted terminals or worn insulation on wires. 3. Install the correct fuses or circuit breakers. 4. Push the thermal overload button to reset it.
M
Melinda ReedAug 23, 2025
How to fix a Haussmann Xpert Sander when the motor won't start?
- O
  ocarterAug 23, 2025
  If the motor of your Haussmann Xpert Sander won't start, it could be due to: * Low voltage. * An open circuit in the motor or loose connections. * The thermal overload protector being activated. To address this: 1. Check the power line for proper voltage. 2. Inspect all lead connections on the motor for loose or open connections. 3. Push the thermal overload button to reset it.
J
janice31Aug 30, 2025
Why Haussmann Xpert DS1800 motor loses power?
- T
  Thomas ThomasAug 30, 2025
  If the motor of your Haussmann Xpert Sander fails to develop full power, and the power output decreases rapidly with a decrease in voltage at the motor terminals, it could be due to: * The power line being overloaded with lights, appliances, and other motors. * Undersized wires or circuits that are too long. * General overloading of the power company’s facilities. To solve this: 1. Reduce the load on the power line. 2. Increase wire sizes or reduce the length of wiring. 3. Request a voltage check from the power company.
J
Jacob HardySep 5, 2025
What to do if workpieces stall while feeding in my Haussmann Xpert DS1800 Sander?
- S
  Scott HickmanSep 5, 2025
  If workpieces stall while feeding through the Haussmann Xpert Sander, it could be due to: 1. Too much material removal per pass. 2. Not enough tension on the feed belt. To resolve this: 1. Reduce the depth of stock removal per pass. 2. See operation, “Adjusting Tracking and Tension of the Feed Belt”.

Haussmann Xpert DS1800 Specifications

General

Brand	Haussmann Xpert
Model	DS1800
Category	Sander
Language	English

Haussmann Xpert DS1800 User Manual

Table of Contents

Questions and Answers:

Haussmann Xpert DS1800 Specifications