Havis C-HDM Series - User Manual

A-
GUIDE RING BUSHING REMOVAL
WE STRONGLY RECOMMEND NOT TO REMOVE THE
GUIDE RING BUSHING, BUT IF REMOVAL OF INNER POLE
IS DESIRED - FOLLOW THIS SIMPLE REMOVAL
INSTRUCTION
INSERT MAXIMUM 1" DIAMETER OBJECT WITH 1.
SUFFICIENT LENGTH AND DROP INSIDE INNER POLE.
MAKE SURE NOTHING PREVENTS GUIDE RING 2.
BUSHING FROM BEING EJECTED UNDERNEATH. HIT
WITH A HAMMER TO FORCE THE GUIDE RING
BUSHING OUT.
7/8" - 1"
DIAMETER
OBJECT
SUPPORT ARM
(OPTIONAL)
B -
INSTALL SPIDER COLLAR (OPTIONAL
COMES WITH C-HDM-401 & 403)
IF MOUNTING THE SPIDER COLLAR TO THE INNER 1.
POLE USE CM003406 REDUCING BUSHING. SPREAD
AND SNAP OVER THE INNER POLE.
LOOSELY ATTACH SPIDER COLLAR TO THE OUTER 2.
POLE OR CM003406. DO NOT MOUNT SPIDER
COLLAR ABOVE OUTER POLE HORIZONTAL CUT.
SPIDER MUST BE
BELOW THIS SLOT
ON THE OUTER POLE
C -
INSTALL OPTIONAL C-HDM-416
IF MOUNTING C-HDM-416 TO THE INNER POLE USE 1.
CM003406. SPREAD THE PIECE AND IT SHOULD SNAP
OVER THE INNER POLE.
ATTACH C-PM-101 TO CLAMP ASSEMBLY USING 2.
LONG CARRIAGE BOLTS INSERTED THROUGH THE
PRINTER AND ONE PIECE OF EXTRUSION.
ATTACH POLE CLAMP TO THE OUTER POLE OR 3.
CM003406. AFFIX SECOND PIECE OF EXTRUSION
AROUND POLE AND LOOSELY TIGHTEN THE
HARDWARE. DO NOT MOUNT CLAMP ABOVE
OUTER POLE HORIZONTAL CUT.
CM003406 REDUCING
BUSHING IS NECESSARY
IF MOUNTING TO
THE INNER POLE.
(USE ONLY ON FIXED
HEIGHT POLES)
C-PM-101
SOLD SEPARATELY
D-
INSTALL GAS SHOCK (OPTIONAL)
(SKIP IF GAS SHOCK IS NOT IN USE) 1.
UNSCREW SMALL PLASTIC DISC FROM SHOCK 2.
INSERT GAS SHOCK ASSEMBLY UPWARD FROM
THE BOTTOM OF HDM POLE ASSEMBLY WITH GAS
SHOCK'S ROD FACING DOWNWARD. GAS
SHOCK WILL SANDWICH BETWEEN MOUNTING
BASE C-HDM-100 SERIES (NOT SHOWN) AND
ACTION ADAPTER C-HDM-300 SERIES (NOT
SHOWN).
ONCE GAS SHOCK SITS PROUD OF THE INNER 3.
POLE REATTACH SMALL PLASTIC DISC
GAS SHOCK
(OPTIONAL)
E -
INSTALL C-HDM-409 OPTIONAL
& COLLAR CLAMP ALIGNMENT
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE 1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE C-HDM-409. 2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER 3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE. 4.
F -
INSTALL C-HDM-410-412 OPTIONAL
THIS CAN BE DONE EITHER AT THIS POINT OR ONCE 1.
THE C-HDM-100 SERIES BASE IS ALREADY IN THE
VEHICLE. YOU WILL NEED THE OFFSET THAT WAS
WIITH THE C-HDM-100 BASE IF APPLICABLE.
DECIDE ON THE ORIENTATION OF THE OFFSET. 2.
ENSURING THAT IF THE HANDLE VERSION OF THE
POLE IS BEING USED THE TWO SLOTS ARE NO MORE
THAN 45 DEG APART IF THIS IS THE CASE ROTATE THE
POLE TO THE CORRECT POSITION.
IF NO HANDLE IS BEING USED ENSURE THE OUTER 3.
POLE SLOT AND THE CLAMP COLLAR SLOT LINE UP.
TIGHTEN ALL THE HARDWARE. 4.
45°
MAX
45°
MAX
SLOTS IN TUBE
AND CLAMP
ALIGNED
HAMMER
PROJECT #
REV. DESCRIPTION DATE BY CHECKED BY
1765
3-13
REVISION DATE CORRECTED TO PT895 DOCUMENTED CHANGE.
NO OTHER CHANGES
8/5/2014 KDAVIS
75 JACKSONVILLE RD,
WARMINSTER, PA. 18974
1-800-524-9900
SIZE
SCALE: 1:8
SHEET 1 OF 4
DO NOT SCALE DRAWING
WEIGHT (LB): 12.634
TITLE:
DWG. NO.
C-HDM_INST
REV
A
3-13
HAVIS, INC.
INSTALLATION INSTRUCTIONS, C-
HDM MOUNTING BASES

Summary

Optional Component Installation Procedures

Guide Ring Bushing Removal

Instructions for removing the guide ring bushing from the inner pole, emphasizing caution.

Install Spider Collar

Guidance on installing the spider collar, including the use of a reducing bushing for inner pole mounting.

Install Optional C-HDM-416

Steps for installing the optional C-HDM-416 component, including attaching the C-PM-101.

Install Gas Shock

Instructions for installing an optional gas shock assembly into the HDM pole assembly.

Install C-HDM-409 Optional & Collar Clamp Alignment

Procedure for installing the C-HDM-409 and aligning the collar clamp, considering handle versions.

Install C-HDM-410-412 Optional

Steps for installing optional C-HDM-410-412, including orientation and alignment of slots.

Mounting Base Installation Methods

Vehicle Mounting Requiring Drilling

Instructions for mounting bases to a vehicle where drilling is required, emphasizing safety.

Flat Surface Mounting

Procedure for mounting bases to flat surfaces, including marking and drilling holes.

Console Side Mounting (Pre-Installed Nuts)

Steps for mounting bases to console side rails with pre-installed nuts.

Console Side Mounting (Pre-Drilled)

Guidance for console side mounting using pre-drilled holes in the console.

Specific Accessory Mounts and Arms

C-HDM-403 Horizontal Printer Mount

Instructions for installing the C-HDM-403 horizontal printer mount, noting console space considerations.

C-HDM-401 Support Arm

Steps for attaching the C-HDM-401 support arm, including finding suitable attachment points.

C-HDM-404 Support Arm

Procedure for installing the C-HDM-404 support arm, primarily for universal floor mounts.

C-HDM-417 Vertical Printer Mount

Instructions for mounting the C-HDM-417 vertical printer mount with C-PM-101.

Attaching Shaft Stop Collar

Guidance on attaching the shaft stop collar for telescoping poles with handles.

General Assembly and Series Connections

General C-HDM-300 Series Install Instructions

General installation steps for C-HDM-300 series mounting devices, including torque specifications.

C-HDM-402 Optional Safety Lock with C-HDM-305

Instructions for mounting the C-HDM-402 safety lock onto the C-HDM-305.

C-HDM-301 to C-MD-200 Series Connection

Steps for connecting C-HDM-301 to C-MD-200 series components.

C-MD-100 Series Installation

Procedure for placing and attaching the C-MD-100 series motion device onto a pole mount.

C-MKM-100 Series to C-HDM-200 Series Connection

Instructions for connecting C-MKM-100 series to C-HDM-200 series using nuts and bolts.

Havis C-HDM Series Specifications

General

Brand	Havis
Model	C-HDM Series
Category	Racks & Stands
Language	English