EasyManua.ls Logo

Haws 1201SFH - User Manual

Haws 1201SFH
21 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
09/19 1200 Series Electric Water Coolers Page 1 of 21
1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424
E-mail: haws@hawsco.com website: www.hawsco.com
No. 0510000866 (5)
Electric Water Cooler and Bottle Filling Stations
MODELS 1201S / 1201SF / 1211S / 1211SF / 1202S / 1202SF / 1212S / 1212SF
1201SFH, 1202SFH, 1211SH, 1211SFH, 1212SH, 1212SFH
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
SAFETY PRECAUTIONS
CAUTION: Disconnect electrical power to outlet before installing or servicing.
NOTICE:
A. The electrical receptacle must have code-approved ground-fault circuit
interrupter (GFCI) protection for personnel.
B. Care should be taken not to damage refrigeration system lines or
electrical wires during installation.
C. Installation must conform to all applicable codes and standards.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
FULL-SCALE ROUGH-IN TEMPLATE PN 0510001007 AVAILABLE UPON REQUEST.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

Table of Contents

Questions and Answers

  • C
    Cassandra GonzalezAug 16, 2025
    How to fix Haws 1201SFH Water Dispenser with no water flow from bubbler?
    • L
      Lisa WatkinsAug 16, 2025
      To address the issue of no water flow from the bubbler in your Haws Water Dispenser, try the following: * Check if the filter has expired. * Ensure the supply valve is open and there's sufficient water pressure. * Confirm the cooler is receiving power. * Inspect and replace the fuse (excluding models 1201S and 1202S). * Press the front button and listen for a click or hum, which indicates the solenoid valve's functionality.
  • M
    Mary WigginsAug 19, 2025
    How to fix Haws Water Dispenser with no water flow from bottle filler?
    • A
      amandavaughnAug 19, 2025
      If your Haws Water Dispenser's bottle filler isn't dispensing water, consider these steps: 1. Check if the filter has expired. 2. Ensure the water supply valve is open and there is adequate water pressure to the cooler. 3. Verify that the cooler is receiving power. 4. Check and replace the fuse (except for models 1201S and 1202S). 5. Clean the bottle filler sensor lens using mild detergent and water. 6. Activate the sensor and listen for a click or hum to determine if the solenoid valve is working.
  • M
    Marc RuizAug 22, 2025
    How to increase water flow from bubbler on Haws 1201SFH Water Dispenser?
    • M
      mmendozaAug 22, 2025
      To resolve low water flow from the bubbler on your Haws Water Dispenser: * Replace the filter. * Ensure a minimum supply pressure of 30 psig. * Confirm the supply valve is fully open. * Unscrew the nozzle and flush it with clean water. * Replace the nozzle.
  • D
    Daniel DudleyAug 25, 2025
    What to do if low water flow from bottle filler Haws Water Dispenser?
    • R
      Ryan MorganAug 26, 2025
      To troubleshoot low water flow from the bottle filler of your Haws Water Dispenser: * Replace the filter. * Make sure that there is a minimum supply pressure of 30 psig. * Ensure the supply valve is in the full open position. * Unscrew the aerator and flush with clean water. * Replace the aerator.
  • J
    james57Aug 27, 2025
    How to stop water from splattering from Haws 1201SFH Water Dispenser bubbler?
    • C
      Christian JohnsonAug 27, 2025
      If the water from the bubbler of your Haws Water Dispenser excessively splatters when contacting the bowl, try these solutions: * Unscrew the bubbler nozzle and flush it with clean water. * Replace the bubbler nozzle.
  • C
    Cody CameronAug 30, 2025
    Why is water splattering from Haws 1201SFH bottle filler?
    • J
      Joseph MillerAug 30, 2025
      To resolve the issue of water from the bottle filler nozzle excessively splattering when contacting the drain basin on your Haws Water Dispenser: * Unscrew the aerator and flush it with clean water. * Replace the aerator.
  • Y
    ybaileySep 2, 2025
    Why is my Haws 1201SFH not dispensing cold water?
    • B
      Brian VincentSep 2, 2025
      To address the issue of your Haws Water Dispenser not dispensing cold water: * Check the thermostat position. * Verify that the compressor is running; the shell should feel warm to the touch after it has been running.
  • D
    Danny FarmerSep 4, 2025
    Why does Haws Water Dispenser bottle filler flow water by itself?
    • D
      Donald ReyesSep 4, 2025
      If your Haws Water Dispenser bottle filler is flowing water by itself: * Note that the unit self-purges every 24 hours if it is not used. * Clean the bottle filler sensor lens with mild detergent and water.
  • B
    blackkevinSep 7, 2025
    What does E009 error mean on Haws 1201SFH?
    • D
      Deborah TaylorSep 7, 2025
      If your Haws Water Dispenser is showing error code E009, indicating the compressor is cycling too frequently, try the following: * Clear the error in programming mode, power cycle the unit, and then check the error again to validate. * Power cycle the unit and ensure the fan runs for approximately 10 seconds initially. * Clean any dust or debris from the condenser fins. * Make sure that the inlet water and ambient temperatures are below the maximum specification.
  • M
    Michael HowardSep 10, 2025
    What does E012 error mean on Haws Water Dispenser?
    • J
      John WileySep 12, 2025
      If your Haws Water Dispenser displays error code E012, indicating the bottle filler sensor is obstructed, try these steps: * Clear the error in programming mode, power cycle the unit, and then check the error again to validate. * Remove any obstruction from the aperture and clean it with a soft cloth that won’t scratch the surface. * Check the aperture for excessive scratches.

Haws 1201SFH Specifications

General IconGeneral
Model1201SFH
CategoryWater Dispenser
MaterialStainless Steel
ColorSilver
Weight15 lbs
InstallationWall Mounted
ADA CompliantYes
FinishBrushed
Number of Stations1
Temperature Range40°F - 100°F
CertificationsNSF/ANSI 61
ActivationSensor
ConstructionStainless Steel

Related product manuals