Haybuster Balebuster 2564

Questions and Answers

M
Michael JohnstonAug 14, 2025
Why does my Haybuster Balebuster 2564 Tractor have excessive vibration?
- L
  Lauren BenjaminAug 14, 2025
  If the Haybuster Tractor experiences excessive vibration, several factors could be the cause. It might be due to a broken flail, which would require a replacement. Another potential cause is a defective cylinder bearing, which also needs replacing. Misaligned or worn PTO parts can also lead to excessive vibration, necessitating replacement of the worn part or the entire PTO. Additionally, a buildup of twine on the rotor, auger, or fan can cause this issue, so remove any twine from these components. Lastly, bent rotor, auger, or fan components can cause vibration and should be replaced as needed.
J
Julie CannonAug 18, 2025
What to do if the forage is too coarse in my Haybuster Tractor?
- B
  Brian SawyerAug 18, 2025
  If the Haybuster Tractor's forage is too coarse, it could be due to a conveyor speed that is too fast, so decrease the conveyor speed. Another possible cause is the slug bar being set too low; raise the slug bar to expose less flail. Also, check if the screen has been removed or is too coarse; in this case, add a screen or install a finer screen.
K
Kristine WallaceAug 21, 2025
What to do if the forage is too fine in my Haybuster Tractor?
- S
  Summer BrooksAug 21, 2025
  If the Haybuster Tractor's forage is too fine, it could be because the conveyor speed is too slow, increase the conveyor speed to resolve this. Alternatively, the slug bar might be set too high, lower the slug bar to expose more flail. Another reason could be that a screen is installed; install a coarser screen to fix this.
B
Brittany DelgadoAug 25, 2025
What to do if my Haybuster Balebuster 2564 will not lift the bale?
- M
  mstoutAug 25, 2025
  If your Haybuster Tractor's machine will not lift the bale, the tractor hydraulic pressure might be too low; check the pressure. Alternatively, hydraulic oil might be leaking by the piston in the cylinder; in this case, repair or replace the hydraulic cylinder.
T
Timothy JonesAug 28, 2025
How to fix a Haybuster Balebuster 2564 when the fan plugs?
- D
  Darius MooreAug 28, 2025
  If the fan plugs in your Haybuster Tractor, reduce the conveyor speed. Adjust the slug bars so less flail is exposed. Install a screen, or install a finer screen.
W
William CochranAug 31, 2025
Why does the forage blow past the bunk when bunk feeding with my Haybuster Balebuster 2564 Tractor?
- J
  James MackAug 31, 2025
  If the forage blows past the bunk when bunk feeding with your Haybuster Tractor, it is because the deflector spout is too high. Lower the deflector spout.
M
monica05Sep 3, 2025
What should I do if the forage blows out of the bunk with my Haybuster Tractor?
- C
  christopherthompsonSep 4, 2025
  To address forage blowing out of the bunk with your Haybuster Tractor, reduce the PTO speed.
J
Jason BrownSep 7, 2025
Why does my Haybuster Tractor have no capacity?
- T
  Teresa WilliamsSep 7, 2025
  If the Haybuster Tractor has no capacity, it is because bale turning is too slow. Open the conveyor speed control valve to resolve this.
A
Amanda FreemanSep 10, 2025
What to do if the bale does not turn in my Haybuster Balebuster 2564 Tractor?
- B
  Bryan BaldwinSep 10, 2025
  If the bale does not turn in your Haybuster Tractor, it is because the bale is lodged in the feeder. Reverse the rotation of the slat conveyor to solve this problem.

Haybuster Balebuster 2564 Specifications

General

Brand	Haybuster
Model	Balebuster 2564
Category	Tractor
Language	English

Haybuster Balebuster 2564 - User Manual

Table of Contents

Questions and Answers

Haybuster Balebuster 2564 Specifications