EasyManua.ls Logo

HBM 70(24) BOUWDROGER - User Manual

HBM 70(24) BOUWDROGER
28 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
P.02 Gelieve te lezen en voor later gebruik bewaren
P.12 Veuillez lire et conserver pour consultation ultérieure
P.22 Please read and keep for future reference
FR
EN
NL
HANDLEIDING - MODE D’EMPLOI - MANUAL
Bouwdroger
Déshumidicateur
Dehumidier
9731
HBM 50(24) BOUWDROGER
9009
HBM 70(24) BOUWDROGER
9732
HBM 90(24) BOUWDROGER
HBM Machines B.V
Grote Esch 1010
2841 MJ Moordrecht
The Netherlands
www.hbm-machines.com
info@hbm-machines.com

Table of Contents

Questions and Answers

  • T
    Timothy CastanedaAug 15, 2025
    Why is my HBM 70(24) BOUWDROGER not working and the display is blank?
    • A
      Amanda ReedAug 15, 2025
      If your HBM Dehumidifier isn't working and the display is blank, it could be due to a power outage or poor connection. Check the power supply and ensure both ends of the power cord are securely connected. Another cause might be that the room temperature is outside the unit's operating range, resulting in a HI or LO error. In this case, modify the room conditions to be between 33 and 100 °F.
  • A
    Amanda AguirreAug 18, 2025
    What to do if my HBM 70(24) BOUWDROGER Dehumidifier shows trouble code E4?
    • K
      Katherine MillerAug 18, 2025
      If your HBM Dehumidifier displays the trouble code E4, it indicates that the pump has detected high water in the reservoir. You should check for clogged drain lines and ensure the pump is working correctly. Service or replace the pump if necessary.
  • J
    Jeanette LopezAug 21, 2025
    How to fix pump alarm error code E4 on HBM 70(24) BOUWDROGER Dehumidifier?
    • J
      James GutierrezAug 22, 2025
      To clear the error code E4 on your HBM Dehumidifier, try disconnecting the power cord and then reconnecting it. Manually check if the pump is working by pressing the pump button (P) to see if it energizes and de-energizes properly, and if water is purged from the system. If you haven’t cleaned the system recently, check the discharge line for obstructions and clean the pump system. If maintenance isn't enough, replace the hoses or pump.
  • J
    Jeff SparksAug 25, 2025
    What does it mean if my HBM 70(24) BOUWDROGER shows E1, L0, and HI at the same time?
    • P
      Patricia YoungAug 25, 2025
      If your HBM Dehumidifier shows E1, L0, and HI simultaneously, it indicates a bad connection, cable, or sensor. Check the cable connection, and replace the cable or sensor.
  • M
    Melissa HughesAug 27, 2025
    Why my HBM Dehumidifier cannot be started?
    • T
      Thomas YoderAug 27, 2025
      Your HBM Dehumidifier might not start if the filter mesh is clogged. Clean the filter to resolve this. Alternatively, the air inlet or outlet may be jammed. Clear any blockage from the air inlet or air outlet.
  • J
    Jacob SanchezAug 30, 2025
    What does trouble code L0 mean on my HBM 70(24) BOUWDROGER?
    • M
      Mary OdonnellAug 30, 2025
      The trouble code L0 on your HBM Dehumidifier means the unit is sensing a room temperature below 33 °F. Increase the room temperature, and check the sensor and sensor cable.
  • C
    Connie HansenSep 2, 2025
    What does trouble code HI mean on my HBM 70(24) BOUWDROGER Dehumidifier?
    • A
      Adam MurphySep 2, 2025
      The trouble code HI on your HBM Dehumidifier indicates that the unit is sensing a room temperature above 100 °F. Decrease the room temperature and check the sensor and sensor cable.
  • J
    jeremy16Sep 5, 2025
    What does error code E1 mean on HBM Dehumidifier?
    • A
      Adam WrightSep 5, 2025
      If your HBM Dehumidifier shows error code E1, it indicates a humidity sensor or communication error. Check that the sensor cable is properly connected, and replace the sensor if necessary.
  • B
    Brittany JenkinsSep 8, 2025
    What does error code E3 mean on HBM Dehumidifier?
    • T
      Traci TurnerSep 8, 2025
      If your HBM Dehumidifier displays error code E3, it signifies a temperature sensor or communication error. Check the sensor cable is properly connected and replace the sensor.
  • J
    Judy LopezSep 12, 2025
    How to restore airflow in my HBM Dehumidifier?
    • M
      Michael LevySep 12, 2025
      If there is no airflow in your HBM Dehumidifier, the filter mesh might be jammed. Clear the filter. Another possible cause is that the unit is not level. Place the unit on a flat surface in a vertical orientation.

Summary

Safety Information

General Safety Precautions

Essential safety precautions for operating and maintaining the dehumidifier.

Control Panel Features

Power and Purge Controls

Instructions for turning the unit on/off and draining the reservoir.

Humidity and Time Settings

Operating Your Dehumidifier

Basic Operation and Important Notes

Unit Setup and Routine Maintenance

Preparing the Dehumidifier for Use

Troubleshooting and Error Codes

Common Machine Operation Issues

Solutions for common problems like no power, no airflow, or unusual noise.

Specific Error Code Diagnosis

Interpreting and resolving specific error codes (E1, E3, E4, LO, HI) displayed by the unit.

Addressing Pump Alarm Error E4

Specific steps to clear and address pump alarm error code E4.

HBM 70(24) BOUWDROGER Specifications

General IconGeneral
Voltage220 - 240 V
Frequency50 Hz
CoolantR290
Dimensions35 x 24.5 x 51 cm
Dehumidification capacity at 30°C / 80% RH24 L/day
Water tank capacity5.5 L
Operating temperature range5°C - 35°C
Noise level48 dB

Related product manuals