Health Zenith SECUR360 HZ-9300-WH User Manual (English)

Questions and Answers:

R
Ryan MooreAug 2, 2025
Why does my Health Zenith Flood Light come on for no apparent reason?
- M
  Matthew MorrisAug 3, 2025
  Your Health Zenith Flood Light might be activating due to several reasons. The motion sensor could be picking up small animals or car traffic, or the sensitivity setting might be too high. Also, check if the DualBrite Duration in the app is set to 3 hours, 6 hours, or dusk-to-dawn, as the light operates normally under these settings. If the outside temperature is much warmer or cooler than a person’s body heat, decrease the sensitivity. Ensure the light isn't wired through a dimmer or timer; if it is, replace it with a standard on/off switch.
D
Derrick RodriguezAug 7, 2025
What to do if my Health Zenith SECUR360 HZ-9300-WH stays on continuously?
- B
  brandi23Aug 7, 2025
  If your Health Zenith Flood Light remains on, it could be due to several factors. The motion sensor might be detecting a heat source such as an air vent or reflective surface, so try decreasing the sensitivity or repositioning the sensor. Ensure the light hasn't been set to 'ON' in the app; if so, switch it to 'AUTO' or 'OFF'. Avoid using a dimmer or timer to control the light; replace them with a standard on/off switch. Lastly, make sure the light isn't on the same circuit as a motor, transformer, or fluorescent bulb; if it is, install it on a separate circuit.
P
Pamela WalkerAug 11, 2025
How to fix Health Zenith Flood Light that will not come on?
- S
  Scott DouglasAug 11, 2025
  If your Health Zenith Flood Light isn't turning on, first ensure the light switch is on. Check the fuse or circuit breaker and replace or reset if necessary. Verify the power pins are correctly aligned with the power block by removing and reinstalling the light on the mounting plate. If it's daytime, the photocell might be in effect, so recheck after dark. For new installations, confirm the wiring is correct. Adjust the motion sensor to cover the desired area, and increase the sensitivity if the outside temperature is similar to body heat. Finally, use the app to ensure the light is set to 'AUTO' mode.
B
barry46Aug 15, 2025
Why does my Health Zenith SECUR360 HZ-9300-WH Flood Light come on during the day?
- J
  Jay WrightAug 15, 2025
  Your Health Zenith Flood Light might be activating during the day if the motion sensor is in a dark location as the light fixture is operating normally under these circumstances. Also, check if the Full Brite Setting in the app is set to 'TEST'. If it is, set it to the 1, 5, or 20 minute setting.
S
Sara MillsAug 20, 2025
Why is my Health Zenith Flood Light flashing on and off?
- S
  Sheri KnightAug 20, 2025
  If your Health Zenith Flood Light is flashing, the lamp heads' heat or light may be triggering the motion sensor; reposition them away from the sensor. Reflected heat from other objects could also be a factor; decrease the sensitivity or reposition the sensor. If the Full Brite Setting is in 'TEST' mode, the light only stays on for 5 seconds; change the setting in the app to 1, 5, or 20 minutes. A Smart Meter nearby might be causing interference; relocate the light fixture away from the meter.
D
Daniel AndersonAug 23, 2025
Why does my Health Zenith Flood Light turn off too late in Dusk-to-Dawn setting?
- J
  James DurhamAug 25, 2025
  Your Health Zenith Flood Light might be turning off late in Dusk-to-Dawn setting because it is installed in a relatively dark location. Try relocating the light fixture or use the 3 hour or 6 hour setting.
C
Christopher SalazarAug 28, 2025
What to do if Health Zenith SECUR360 HZ-9300-WH flashes once then stays off in manual mode?
- D
  daniel62Aug 28, 2025
  If your Health Zenith Flood Light flashes once and then stays off in manual mode, it's likely that the motion sensor is detecting light from the lamp heads. Reposition the lamp heads to keep the area below the motion sensor relatively dark.