To Next PageTo Next PageWhat to do if the control light of the charging station in my Heiniger Pet Care Product is not on?
If the control light of the charging station for your Heiniger Pet Care Product is not on, first check if the charging station is properly connected to the power supply. If not, connect it. If it is correctly connected then the charging station might be faulty and require inspection.
Why is my Heiniger Pet Care Product clipper cutting badly or not at all?
Your Heiniger Pet Care Product clipper might be cutting poorly or not at all due to several reasons. The clipper blade might be blunt, requiring re-sharpening by a service center. Insufficient oiling of the clipper blades, ideally every 15 minutes, can also cause this issue. Ensure you're only clipping dry hair, as wet hair can impede the cutting process. Hairs jammed between the top and bottom blades can also be a culprit; remove the clipperhead, push the top blade half away, and clear any lodged hairs. Finally, the clipperhead might have too little clipping pressure, which requires inspection.
How to resolve a Heiniger Pet Care Product running time of a fully charged battery that is too short?
If the running time of your fully charged Heiniger Pet Care Product battery is too short, and/or the blades are getting hot, it could be due to insufficient oiling of the clipper blades. Make sure you oil the clipper blades. It may also be due to using a dead, not fully charged, or defective battery. Ensure that you only use an intact and completely charged original battery.
What to do if top blade does not move on Heiniger Pet Care Product?
If the top blade of your Heiniger Pet Care Product does not move, it may be because the clipperhead is not well engaged. Ensure that you engage the clipperhead correctly when the motor is running. Alternatively, the turning lever could be defective, requiring replacement.
What to do if my Heiniger saphir Hair Clipper motor is not running?
If the Heiniger Hair Clipper motor isn't running, there are several potential causes. First, the battery might be dead, so try charging it. Second, the contacts could be dirty; switch the clipper off and clean them. Third, the battery itself may be faulty, requiring replacement. Finally, a burning smell from the motor housing indicates the motor has burned out and needs replacement, along with the electronics.
What to do if Heiniger Commercial Food Equipment LED flashes red/green?
If the LED on your Heiniger Commercial Food Equipment flashes alternately red/green, this indicates a faulty battery. Replace the battery. If two batteries are inserted into the charging station at the same time, test batteries individually.
What to do if Heiniger Commercial Food Equipment battery runs short and blades get hot?
If the running time of a fully charged battery is too short, and/or the blades are getting hot on your Heiniger Commercial Food Equipment, it could be due to insufficient oiling of the clipper blades, so oil clipper blades. Alternatively, a dead, not fully charged, or defective battery may have been used, so ensure you only use an intact and completely charged original battery.
What to do if Heiniger Commercial Food Equipment motor does not work?
If the motor of your Heiniger Commercial Food Equipment does not work, the issue could be a faulty motor and/or electronics, which should be replaced. Another possibility is a blocked clipperhead, which requires cleaning and oiling.
How to fix a Heiniger Electric Shaver when the top blade does not move?
If the top blade of your Heiniger Electric Shaver isn't moving, it could be because the clipperhead isn't properly engaged (engage the clipperhead correctly when the motor is running) or the drive carrier is defective (replace drive carrier).
What to do if my Heiniger Electric Shaver cuts badly or not at all?
If your Heiniger Electric Shaver is not cutting well, it could be due to several reasons. The clipper blade may be blunt and need resharpening by a service center. Ensure the clipper blades are oiled every 15 minutes. Only clip dry hair, as wet hair can affect performance. Hairs jammed between the top and bottom blades can also cause this issue; remove the clipperhead, push the top blade half away from the clipperhead, and clear any hairs. Finally, the clipperhead may have too little clipping pressure, requiring inspection by a service center.
General| Brand | Heiniger |
|---|---|
| Model | saphir |
| Category | Hair Clipper |
| Language | English |
