Hella marine LED Navigation Lamps offer many advantages over conventional bulb lamps.
Signicantly reduced power consumption, ultra long life and high tolerance to shock and
vibration make the LED lamps the ideal choice for the harsh marine environment.
The Hella marine NaviLED
®
360 series are Precision Optical Instruments, tested and type
approved to comply with international maritime regulations. They are covered by a 5 year
warranty.
Wiring and Electrical Protection
LED modules are polarity conscious. This lamp is protected against reverse polarity connection,
reverse polarity will not damage this product but will inhibit its function.
HELLA marine recommends wire connections be soldered, and heat shrink tubing applied to seal
the joint.
Each lamp must be protected against short circuit by a fuse rated at 5 amperes maximum.
Note: Do not attempt to open, no serviceable part inside.
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress
possible interference, both emission as well as susceptibility, to the limits prescribed in
international regulations.
Colour Connect to
Black Negative (-ve)
Red Signal (+ve)
Wiring Colour Coding
Designed and Manufactured in New Zealand
958 315-60 V01 (ENG-GER-FR)
INSTRUCTION SHEET: NaviLED
®
360 Compact Pole Mount
2 Nautical Mile All Round White / Anchor Lamp
Product Specications
Housing Material UV resistant high impact plastic
Lens Material Heavy duty Grilamid
®
Minimum Visible Distance 2 Nautical Miles
Cable Pre-wired with twin core marine cable
Operating Voltage Multivolt
TM
9-33V DC
Power Consumption Less than 1W (0.08A @ 12V / 0.04A @ 24V)
Degree of Protection IP 67 - Completely Sealed
Approvals USCG, IMO COL REG 72, Wheelmark
Correct Positioning
NaviLED
®
360 Compact All Round / Anchor
Lamps must be installed as follows:
When the lamp operates, the light should not
be obstructed or concealed by masts,
topmasts or structures, i.e. Installed on the
highest point of a vessel so the light arc is
unbroken.
All Round lamps must be positioned as close
as practicable to the fore and aft centre line
of a vessel. (see Fig.1)
The All Round white lamp on a power driven
Vessel less than 12m in length shall be
installed at least one meter higher than the
sidelights.
The lamp must be installed so that the
horizontal surface of the base is parallel to
the vessel's water line. (See Fig.2)
Fig. 1 On the fore and aft centre line.
Fore
Centre Line
Aft
Fig. 2 Installed with base parallel to vessel's
water line.
Vessel's water Line
Installation Instructions
1. Fixed Pole mount: Ensure mounting surface is at and on the vessels centre line (see above).
Use the provided screws to secure taking care not to over tighten.
2. Fold-down Pole mount: A removable wedge is supplied for installations onto different surface
cambers. Use the provided screws to secure taking care not to over tighten. Once mounted the
base can be adjusted through 180 degrees, when the desired angled is reached secure by
tightening the locking collar.
3. Plug-in Pole mount: Mount base separately and connect wiring. Use the provided screws to
secure taking care not to over tighten. Insert lamp into base and x with locking collar.
Ensure rubber cap, as provided, is used to cover socket when pole is removed.
1. Fixed pole 2. Fold-down pole 3. Plug-in pole
MAX 3 NmMAX 3 NmMAX 3 Nm
The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for
powerboats and/or sailing vessels up to 12 m (39’) in length.
Mounting position of the lamps:
- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4).
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or
persons. The lamps should also be tightly secured in position
2010 series lamps Mounting Instructions
*
) Angle of 7.5 °
(25° for sailing vessels).
Maintenance
- The lens may be cleaned with a soft brush.
- Only cleansers suitable for polycarbonate plastic may be used.
- Do not wash with harsh or abrasive cleaners.
(1) Masthead lamp (white)
(2) Stern lamp (white)
(3) Starboard / port lamp
(4) Waterline (CWL)
(5) Thwartships plane
(6) Vessel centre line
(7) green
(8) red
(9) white
Mounted with
swivel bracket
Mounted with
plug-in bracket
Ø 3mm
Ø 3mm
Ø 3mm
Ø 3mm
Mounted with tel-
escope bracket
Mounted with
standard bracket
993 609-00
The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for
powerboats and/or sailing vessels up to 12 m (39’) in length.
Mounting position of the lamps:
- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4).
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or
persons. The lamps should also be tightly secured in position
2010 series lamps Mounting Instructions
*
) Angle of 7.5 °
(25° for sailing vessels).
Maintenance
- The lens may be cleaned with a soft brush.
- Only cleansers suitable for polycarbonate plastic may be used.
- Do not wash with harsh or abrasive cleaners.
(1) Masthead lamp (white)
(2) Stern lamp (white)
(3) Starboard / port lamp
(4) Waterline (CWL)
(5) Thwartships plane
(6) Vessel centre line
(7) green
(8) red
(9) white
Mounted with
swivel bracket
Mounted with
plug-in bracket
Ø 3mm
Ø 3mm
Ø 3mm
Ø 3mm
Mounted with tel-
escope bracket
Mounted with
standard bracket
993 609-00
The Hella marine Series 2010 navigation and signal lamps comply with USCG A-16 requirements for
powerboats and/or sailing vessels up to 12 m (39’) in length.
Mounting position of the lamps:
- Port and starboard navigation lamps (3) must be mounted with their back plate parallel to the vessel
centre line (6), in the same thwartships position (5) and at the same height above the waterline (4).
- Masthead (1) and stern lamps (2) as well as anchor lights must be mounted above the vessel centre
line (6).
- All lamps must be mounted in a vertical position with their back plate perpendicular to the waterline.
- When operating, the light should not be obstructed or concealed by superstructures, other objects or
persons. The lamps should also be tightly secured in position
2010 series lamps Mounting Instructions
*
) Angle of 7.5 °
(25° for sailing vessels).
Maintenance
- The lens may be cleaned with a soft brush.
- Only cleansers suitable for polycarbonate plastic may be used.
- Do not wash with harsh or abrasive cleaners.
(1) Masthead lamp (white)
(2) Stern lamp (white)
(3) Starboard / port lamp
(4) Waterline (CWL)
(5) Thwartships plane
(6) Vessel centre line
(7) green
(8) red
(9) white
Mounted with
swivel bracket
Mounted with
plug-in bracket
Ø 3mm
Ø 3mm
Ø 3mm
Ø 3mm
Mounted with tel-
escope bracket
Mounted with
standard bracket
993 609-00
To Next Page
Need help?
General
