EasyManua.ls Logo

HERKULES TKS 1500 S - User Manual

HERKULES TKS 1500 S
240 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
03-2015
Art.-Nr. 390 1306 005
D
Tischkreissäge
Original-bedienungsanleitung
FIN
Pyörösahapenkki
Käännös alkuperäisestä käyttöohjeesta
GB
Circular saw bench
Translation from the original language
CZ

Překlad z originálního návodu
SK

Preklad originálu - Úvod
SLO

Prevod originalnega besedila
SE
Bordscirkelsåg
Översättning från originalspråket
NO
Bordsirkelsag
Oversettelse fra originalspråket
DK
Bordrundsav
Oversættelse fra originalt sprog
FR
Scie circulaire à table
Traduction du manuel d‘origine
E
Mesa de sierra circular
Traducción del idioma original
I
Sega circolare da banco
Traduzione dalle istruzioni d’uso originali
EST
Ketassaagpink
Originaal juhend
LV

Oriģinālā lietošanas pamācība
LT

Pirminės instrukcijos
TR

rjinal operasyon el kitabından çevirilmiştir
HR

Prijevod s izvornog jezika
HU

Az eredeti használati utasítás fordítása
IS
Hringlaga sá bekkur
Þýðing úr frummálinu
BIH

Prijevod originalnog uputstva za upotrebu
RS

Prevod originalnog uputstva za upotrebu
RU

Перевод оригинального руководства по эксплуатации
BG

Превод от оригиналния език
NL
Tafelcirkelzaag
Vertaling uit de oorspronkelijke taal
TKS 1500 S
Art.-Nr. 390 1306 931 / 390 1306 947

Table of Contents

Questions and Answers

  • O
    ortizsarahJul 25, 2025
    What to do if my HERKULES Saw motor does not start?
    • T
      timothysmithJul 25, 2025
      If the motor of your HERKULES Saw fails to start, there are several potential causes. First, check the mains fuse to ensure it hasn't failed. Next, inspect the extension cable for any defects and replace it if necessary. If these steps don't resolve the issue, the connections at the motor or switch, or the motor or switch itself, may be defective and should be checked by an electrician.
  • J
    Jessica LoweryAug 1, 2025
    Why does my HERKULES Saw motor not perform and the fuse activates?
    • S
      Susan HernandezAug 1, 2025
      If the motor of your HERKULES Saw isn't performing well and the fuse activates, it could be due to a couple of reasons. The cross-sectional area of the extension cable might not be sufficient, so refer to the electrical connection guidelines. Also, overloading due to a blunt saw blade can cause this issue, so try replacing the saw blade.
  • C
    Caroline RichardsonAug 9, 2025
    What to do if there are fire stains at the cutting surface when using my HERKULES Saw?
    • L
      laurenmillerAug 9, 2025
      If you notice fire stains on the cutting surface while using your HERKULES Saw, it's likely due to a blunt or incorrect saw blade. Try sharpening or replacing the saw blade with a new one.
  • Y
    yangkevinAug 16, 2025
    Why does the saw blade come loose after switching off the motor on my HERKULES Saw?
    • B
      Brian MartinAug 16, 2025
      If the saw blade of your HERKULES Saw comes loose after you switch off the motor, it's likely because the fastening nut is too loose. Tighten the fastening nut, remembering that it uses a right-handed thread.

HERKULES TKS 1500 S Specifications

General IconGeneral
Power1500 W
Blade diameter254 mm
Weight21 kg
Saw blade bore30 mm
Engine Power1500 W
Voltage230 V
Frequency50 Hz

Related product manuals