Installation Instructions
5200 Series Electric Strike
HES, Inc.
Phoenix, AZ
800-626-7590
www.hesinnovations.com
1
Electrical Specifications
Minimum Wire Gauge Requirements
(Based on Round Trip)
Solenoid Voltage
12 VDC 24 VDC
200 feet or less
200 – 300 feet
300 – 400 feet
18 gauge
16 gauge
14 gauge
20 gauge
18 gauge
16 gauge
3
ASSA ABLOY, the global leader
in door opening solutions
Product Components
1
2
5200 Electric Strike Body Trim Enhancer 12-Volt and 24-Volt Pigtails
Electrical Ratings for Solenoid
Continuous Duty
12 VDC
50
.24
24 VDC
200
.12
Resistance in Ohms
Amps
Solenoids are rated at +/- 10% indicated value.
*10% maximum duty cycle (2 minutes maximum on time)
Indoor use only
4
Cutout Templates for Frame Preparation
© 2015, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.
3059006.002 rev C
1
2
3
Diagram 1: Product Components
Intermittent Duty*
12–16 VAC
50
.24 – .32
24 VAC
200
.12
Resistance in Ohms
Amps
501 Faceplate Option (4-7/8” x 1-1/4”), Square Corners and Flat Faceplate
Used with cylindrical locksets in ANSI metal jambs
501A Faceplate Option (4-7/8” x 1-1/4”), Radius Corners and Flat Faceplate
Used with cylindrical locksets or spring latches in aluminum frames
[mm]
Inches
1 -1/4"
[31.8]
4 -7/8"
[124]
3 -3/8"
[85.7]
13/16"
[20.6]
3/32"
[2.3]
4 -7/8"
[124]
4 -1/8"
[104.8]
1 -7/16"
[36.6]
1 -1/4"
[31.8]
R 1/8"
[3]
3 -3/8"
[85.7]
1 -1/4"
[31.8]
4 -7/8"
[124]
13/16"
[20.6]
[2.3]
3/32"
[mm]
Inches
1 -1/4"
[31.8]
4 -7/8"
[124]
4 -1/8"
[104.8]
1 -7/16"
[36.6]
[mm]
Inches
3-3/8"
[85.7]
13/16"
[20.6]
3/32"
[2.3]
1 -7/16"
[36.5]
7-15/16"
[201.6]
1 -7/16"
[36.6]
7 -15/16"
[201.6]
7 -7/16"
[189]
1 -7/16"
[36.6]
R 3/16"
[4.1]
502 Faceplate Option (7-5/16” x 1-7/16”), Radius Corners and Flat Faceplate
Used with cylindrical locksets or spring latches in aluminum frames
[mm]
Inches
1 -1/4"
[36.5]
3 -3/8"
[85.7]
6 -7/8"
[174.3]
13/16"
[20.6]
3/32"
[2.3]
6 -7/8"
[174.3]
6 -1/8"
[155.6]
1 -1/4"
[31.8]
1 -7/16"
[36.6]
R 3/16"
[4.1]
503 Faceplate Option (6-7/8” x 1-1/4”), Radius Corners and Flat Faceplate
Used with cylindrical locksets or spring latches in aluminum frames
[mm]
Inches
10"
[254]
1 -3/8"
[34.9]
3 -3/8"
[85.7]
13/16"
[20.6]
3/32"
[2.3]
1 -3/8"
[34.9]
10"
[254]
8 -1/2"
[215.6]
8 -1/2"
[215.6]
1 -7/16"
[36.6]
1 -3/8"
[34.9]
R 1/8"
[4]
504 Faceplate Option (10” x 1-3/8”), Radius Corners and Flat Faceplate
Used with cylindrical locksets; four-point mounting for wood installations
NOTE: The 5200 has an in-frame horizontal adjustment range of about 1/4” (6.4 mm) to allow adjustment of the electric strike in the frame
opening to accomodate for the horizontal position of the latchbolt after the strike has been installed. The “Adjusting the Horizontal”
section provides steps for this adjustment.
To Next Page
Need help?
General
