Heylo K 170 - User Manual

Questions and Answers

M
martin91Aug 17, 2025
What to do if the Heylo Heater burner starts up, but indicates interference, and the red signal lamp lights up?
- K
  Kristopher MorganAug 17, 2025
  If the Heylo Heater burner starts but shows interference with the red lamp lit, the issue could stem from several causes: * The oil tank may be empty, in which case you should refill it. * The oil pipe might not be connected, or the main tap could be closed; inspect the pipeline and main tap. * A dirty oil filter can cause this issue, so clean the nozzle filter, pump filter, and pre-filter. If needed, change the nozzle. * The oil suctioning pipe may not be sealed properly, causing the pump to suck in air. Ensure the oil suctioning pipe is sealed and that the oil in the reverse flow pipe is free of bubbles. * Lastly, the oil pump might not be producing enough pressure. In this case, set the pressure correctly.
J
Joseph WilliamsAug 20, 2025
What to do if the Heylo K 170 burner flame goes out after starting up or burns intermittently?
- J
  Juan TaylorAug 20, 2025
  If the flame of your Heylo Heater goes out after starting or burns intermittently, consider these potential causes and solutions: * A dirty photo conductive cell could be the culprit. Pull it out and wipe it with a clean cloth, especially if the room is dusty. * Dirty oil filters can also cause this issue. Check and clean all oil filters, including pre-filters, pump filters, and nozzle filters. * If the oil suctioning pipe isn't sealed properly and the pump is sucking in air, seal off the oil suctioning pipe and tighten all screws. Ensure the oil in the reverse flow pipe is free of bubbles. * A blocked burner nozzle could be the problem. Replace it with a new one instead of attempting to clean it. * Combustion air might not be properly set.
R
Robert MendezAug 23, 2025
What to do if Heylo K 170 burner starts up, but does not ignite, indicates interference, red lamp lights up?
- F
  Felicia BradleyAug 23, 2025
  If your Heylo Heater's burner starts up but doesn't ignite, and a red lamp indicates interference, consider these solutions: * Check the tuyere connection, as there may be no ignition spark. * Also, inspect the tuyere connection if there are carbon deposits on the ignition electrodes or if they are displaced. Ensure to pull out the mains plug or switch off the power supply before checking. * If the burner nozzle is blocked, unscrew it and replace it with a new one. Avoid cleaning the old nozzle.
A
Angela CookAug 27, 2025
Why does my Heylo K 170 room thermostat switch the burner off before the desired room temperature is reached?
- E
  Emily JenkinsAug 28, 2025
  If your Heylo Heater's room thermostat switches off the burner prematurely, it might be because the thermostat is placed where it's exposed to hot air or heat sources like sunlight, machinery, or hot water/steam pipes. Try moving the thermostat to a different location.
J
Jeremy JonesAug 30, 2025
What causes a Heylo K 170 Heater burner to not switch off?
- M
  Martin ReevesAug 30, 2025
  If the burner on your Heylo Heater doesn't switch off, there are a couple of potential causes: * The room thermostat might be in an unsuitable location. Ensure it's placed away from cold airflows from windows or doors. Relocate the thermostat if needed. * The room thermostat may be defective.
K
kelly99Sep 1, 2025
What to do if the ventilator of Heylo K 170 does not start up?
- M
  Mark LynnSep 2, 2025
  If the ventilator of your Heylo Heater fails to start: * Check if the temperature regulator 3S2.1 is functioning and replace it if necessary. * Verify the power supply to the ventilator drive using a voltage tester on the terminal strip X2 (terminals 1, 2, 3).
T
Tamara ClarkSep 4, 2025
What to do if my Heylo Heater burner is not running?
- C
  curtis21Sep 4, 2025
  If the burner isn't running, here's what you can check: * Ensure there's a power supply using a voltage tester or lamp. Turn on the main switch, replace the fuse, and inspect the supply line for loose connections. * If using a room thermostat, make sure it's set above the current room temperature. * If the automatic oil firing device indicates a malfunction, wait about a minute, then switch on the illuminated button to suppress interference. The disturbance indication and signal display should turn off, and the burner will attempt to restart. * If the safety temperature limiter has interrupted the power supply, identify and eliminate the cause of overheating, such as resistance to suction or blowing.
J
Jenna MooreSep 6, 2025
Why does my Heylo Heater burner start but then show interference with the red light on?
- M
  Mr. Allen LeSep 6, 2025
  If your Heylo Heater burner starts but then indicates interference with the red light on, the issue could be due to: * An empty oil tank – Refill the oil. * A disconnected oil pipe or closed main tap – Check the pipeline and main tap. * A dirty oil filter – Clean the nozzle filter, pump filter, and pre-filter. If needed, change the nozzle. * An oil suction pipe that isn't sealed, causing the pump to suck in air – Seal off the oil suction pipe, ensuring the oil in the reverse flow pipe is free of bubbles.
T
Tammy ThomasSep 9, 2025
How to fix a Heylo Heater when the burner starts but doesn't ignite and the red lamp lights up?
- P
  prowlandSep 9, 2025
  If the burner starts but doesn't ignite and the red lamp lights up, consider these solutions: * Check the tuyere connection. Disconnect the heater from the power supply and inspect the connection. * Unscrew the burner nozzle and replace it with a new one if there are carbon deposits on the ignition electrodes or if they are displaced. Never attempt to clean the nozzle! * If the burner nozzle is blocked, keep changing it, opened, cleaned nozzles never burn flawlessly.
T
Teresa LeSep 12, 2025
What to do if the oil pump of my Heylo Heater is not producing any pressure?
- R
  Robert ClementsSep 12, 2025
  If the oil pump isn't producing pressure, the coupling or pump may need to be changed. You can activate the button for removing disturbances on the control unit.