Hiland Photocell P5200 User Manual

1
Photocell P5200 user manual
I. Technical Specification
1. Working voltage: 12~24VAC/DC
2. Working current(24VDC):emitter: ≤8mA receiver: ≤30mA
3. Photocell wavelength: 940nm
4. Angle of emission: ≤±5º
5. Receiving range: ≥12m
6. Angel adjustment of PCBA: 0～180 º
7. Working temperature: -20º～+60℃
8. Relay contact loading capacity: 1A/30VDC
9．Size: 100*40*35mm
II. Safety Instruction
1. For security, please read the user manual carefully before initial operation;
2. This photocell is without any fuse, so Please make sure the power is off before installation;
3. Only used this system that do not cause any danger life or property during the running failure or its security risks eliminated;
4. Please guarantee the products used in effective working range.
III. Picture Display
Wiring diagram• Size
IV. Installation instruction
4.1 Receive module J2 in pic 3 is the option switch of photocell switch.
4.1.1 When the short circuit cap on NO, The photocell will be Normal Open.
4.1.2 When the short circuit cap on NC, the photocell will be normal closed.
4.2. Installation
4.2.1The photocells should be installed more than 20cm above the ground (to avoid reflection), and the distance between emitter
and receiver shall be more than 50cm.
4.2.2 End user should install the photocell on the back of the direct sunlight or other strong light source (±5º) to keep photocell
work well steadily.
4.2.3 Avoid installing other infrared photocell emitters within the effective distance of receiver
4.2.4 If the end user need to install other photocells in one same straight line , the receivers could be installed in the two ends and
the emitters could be back-to-back installed
4.2.5 Stable installation could avoid the signal of emitter and receiver skewing due to lightly vibrate and the malfunction.
4.2.6 Connect the power after the inspection, when short circuit cap at NO, emitter module LED turns on, receiver
module LED turns on, receiver module contact at off; when make the cap of emitter and receiver in alignment, receiver
module LED is off, NC/NO is on; when something or someone shelter the sensor, receiver module LED will turn on , NC/NO
contact is off. When short circuit cap at NC, the state of NO/NO is opposite to the above phenomenon
J2
Pic 3

Hiland Photocell P5200 Specifications

General

Model	P5200
Type	Photocell
Brand	Hiland
Voltage	120-277VAC
Wattage	1000W
Load Current	10A
Material	Plastic
IP Rating	IP65
Category	Accessories
Operating Temperature	-40°C to 70°C

Summary

Technical Specifications

Working Voltage and Current

Details on operating voltage range and current consumption for emitter and receiver modules.

Photocell Characteristics

Information on photocell wavelength, emission angle, and receiving range.

Physical and Environmental Specs

Covers angular adjustment, operating temperature, and overall dimensions of the unit.

Relay Contact Rating

Specifies the capacity of the relay contact for DC load switching.

Safety Instructions

Pre-Operation Safety Checks

Essential safety guidelines to follow before initial operation and installation.

Usage Precautions

Instructions on proper usage, power handling, and risk mitigation.

Picture Display and Wiring

Component Identification

Visual representation of the emitter and receiver modules, including connection points.

Wiring Diagram and Options

Details on the wiring diagram, including jumper settings for Normal Open/Closed operation.

Installation Instructions

Mounting and Placement Guidelines

Recommendations for installing the photocell to ensure optimal performance and avoid interference.

Operational Checks and Connections

Steps for connecting power and verifying module status based on jumper settings.

Step-by-Step Installation Pictures

Accessory Preparation and Mounting

Visual guide for preparing accessories, fixing the holder, and drilling mounting holes.

Wiring and Final Assembly

Illustrations showing wire connection, PCBA angle adjustment, and cover installation.