Hiland R5101 User Manual

R510X user manual Version A6
R510X 1-channel receiver user manual
I. Safety Instruction
1． For security, please read instructions carefully before initial operation; making sure that the power is off before connection.
2． Please clear the memory before initial operation. (Ref: Erasing ALL learned/memorized Transmitters）
3． Do not learn the remote control when motor is operating in order to avoid mis-operation.
4． The received signal may be interfered by other communication devices. (e.g. the wireless control system with the same frequency range)
5． It is forbidden to control the high-risk coefficient equipment / system. (e.g. cranes)
6. It is used only for the manual remote control and wireless control equipment / system which must not endanger life or property
during running failure, or its security risks have been eliminated
7. It should be applied in dry indoor place or in the electric appliance place.
8. If connected wire is too long , the receiver may work unstable
II. Technical parameters III. Connection Instruction
1.Working voltage:12-24VAC/DC
2. Temperature range:-20℃ to 60℃
3. Working frequency:433.92MHz
4. Stored transmitters: Rolling code 30-300PCS;
fixed code 60-600PCS
5.Relay contact load capacity:：1A,30V DC
6.Size:58*34*20mm
7.Weight: 36g
IV. Set up and working process
4.1 Learning transmitter: Press the learning button S1 of the receiver, then LED is red. Press any one of the transmitter twice times,
LED flickers and continues on several seconds, then turns into green. It is indicated the learning is successful.
4.2 Deleting transmitter: Press the learning button S1 for a long time, the indicating lamp is red for 8 seconds, and then turns into green,
release the learning button, LED is red for 2 seconds and then turns into green; it is indicated the deleting is successful.
4.3 Latch and non-latch: It’s non-latch when no short circuit cap on LATCH , It’s latch when there’s short circuit cap on LATCH.
4.4 Self-learning function: Use the transmitter that already has been learned as mother transmitter, it can start the learning function and
learn new transmitter without pressing any learning button. (Press button 1 and button 2 at the same time and then press button
2 to let the receiver enters into the learning process )
V. Operation
5.1 Receiver can learn transmitter after pressing any button of the transmitter .
5.2 Only one button can be learned into the receiver for a transmitter. Eg:button 1 will be replaced if you learn button 2 after learning button 1.
5.3 Non-latch: Keep pressing the button, receiver starts working. Release the button, receiver stops working .
5.4 Latch: Press the button, receiver starts working. Press button again, receiver stops working .
VI. Model list
MODEL(12-24V AC DC)
R5101
R5102
R5103
R5104
R5105
R5106
R5107
R5108
R5166
R5167
R5170
R5171
Frequency
433.92Mhz
Code
Rolling code
Fixed code
Open code
Transmitter stored
30
30
300
300
60
60
600
600
30
30
300
300
The interpretation and ownership of this manual belong to Hiland company. Any change of the product can be without prior notice.

Hiland R5101 Specifications

General

Brand	Hiland
Model	R5101
Category	Receiver
Language	English

Summary

Safety Instruction

Read Instructions Before Operation

Ensure power is off before connection for security and proper initial operation.

Clear Memory Before Initial Use

Erase all learned/memorized transmitters prior to the first operation.

Avoid Learning During Motor Operation

Do not learn the remote control while the motor is operating to prevent mis-operation.

Signal Interference Warning

Received signals may be affected by other communication devices on the same frequency range.

Prohibited for High-Risk Equipment

It is forbidden to control high-risk coefficient equipment or systems, such as cranes.

Intended Use for Control Systems

Used only for manual and wireless control systems where failure poses no danger to life or property.

Suitable Installation Environment

Should be applied in dry indoor places or within the electric appliance place.

Wire Length Impact on Stability

If the connected wire is too long, the receiver may work unstably.

Technical Parameters

Working Voltage Specification

Specifies the operating voltage range for the receiver as 12-24VAC/DC.

Operating Temperature Range

Defines the operational temperature limits for the device, from -20°C to 60°C.

Working Frequency

States the operational frequency of the receiver is 433.92MHz.

Stored Transmitter Capacity

Details capacity for rolling code (30-300PCS) and fixed code (60-600PCS) transmitters.

Relay Contact Load Capacity

Specifies the maximum load capacity of the relay contact as 1A, 30V DC.

Device Dimensions

Provides the physical size of the receiver as 58*34*20mm.

Device Weight

States the weight of the receiver is 36g.

Set Up and Working Process

Learning a Transmitter

Procedure to pair a transmitter: press learning button, press transmitter twice, LED confirmation.

Deleting Transmitters

Process to erase stored transmitters: long press learning button, LED indications confirm deletion.

Latch and Non-latch Functionality

Explains latch mode (short circuit cap on LATCH) vs. non-latch mode.

Self-Learning Function

Method to learn new transmitters using an already learned transmitter as a mother transmitter.

Operation Modes

Transmitter Learning Initiation

Receiver can learn transmitters after pressing any button on the transmitter.

Single Button Learning

Only one button per transmitter can be learned; subsequent learning overwrites previous.

Non-latch Operation

Receiver operates while button is pressed and stops when released.

Latch Operation

Receiver starts working on button press and stops on subsequent press.

Model List