Hillsdale 4090P User Manual

STAIRCASE LOFT BED
Assembly Instructions Page 1 of 10
Item No. 4090P, 5090P, 6090P, 7090P
1. Follow the information on the warnings appearing on the upper bunk end structure and on the
carton. Do not remove warning label from bed.
2. Always use the recommended size mattress or mattress support, or both, to help prevent
entrapment or falls.
3. Surface of mattress must be at least 5 inches (127 mm) below the upper edge of guardrails.
4. Do not allow children under 6 years of age to use the upper bunk.
5. Prohibit more than one person on the upper bunk.
6. Periodicall y, check and ensure that the guardrail, stairs, and other components are in their proper
position, free from damage, and that all connectors are tight.
7. Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8. Always use the stairs for entering and leaving the upper bunk.
9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
10. Use of a nightlight may provide added safety precaution for a child using the upper bunk.
11. Always use guardrails on both long sides of the upper bunk. If bunk bed will be placed next to the
wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent
entrapment between the bed and wall.
12.
13. Keep these instructions for future reference.
!
!
STRANGULATION HAZARD
Never attach or hang items to any part of the bunk bed that are not designed for use with the bed;
including, but not limited to, hooks, belts and jump ropes.
SIZE OF MATTRESS AND FOUNDATION
Use only mattress, foundation and deck combined which is 74-75 inches long and 37 ½-38 ½ inches wide
on upper bunk and same mattress size for lower bunk (74-75 inches long and 37 ½-38 ½ inches wide)
. Ensure thickness of mattress and foundation combined does not exceed 8 inches and the mattress is at
least 5 inches below upper edge of guardrails.
SAFETY WARNINGS
SAFETY FIRST!
All of Hillsdale’s Bunkbeds were
designed and manufactured with
your child’s safety as our top
priority.
Their unparalleled strength is a
bi-product of the safety design.
Our bunks meet all compliance
with ASTM F 1427-13 “Standard
for Bunk Beds” and Code of
Federal Regulations (CFR) 1213
“Safety Standards for Entrapment
Hazards in Bunk Beds” and
(CFR) 1513 “Requirements for
Bunk Beds”.
between us as the manufacturer,
and you as a guardian. Please
read and consider the
warnings listed on this page
when choosing a mattress and
discussing rules of use with your
child.
REPLACEMENT PARTS
Replacement parts, including
additional guardrails, may be
obtained from any of Hillsdale’s
dealers.
Hillsdale Furniture 3901 Bishop Lane, Louisville, KY 40218 www.hillsdalefurniture.com

Hillsdale 4090P Specifications

General

Brand	Hillsdale
Model	4090P
Category	Indoor Furnishing
Language	English

Summary

Safety Information

SAFETY WARNINGS

General safety warnings for bunk bed use, including age restrictions and proper usage.

STRANGULATION HAZARD

Warning against attaching items to the bed that could cause strangulation.

SIZE OF MATTRESS AND FOUNDATION

Specifies mattress and foundation dimensions for safe use and to prevent entrapment.

Product Introduction and Support

INTRODUCTION

Provides initial guidance and recommended steps before beginning product assembly.

CUSTOMER SUPPORT

Information on how to contact the retailer for missing parts or assistance.

Parts and Tools Required

PARTS LIST

Lists all components and hardware necessary for the assembly of the bunk bed.

Other Tools Required

Lists tools not included with the product but necessary for assembly.

Assembly Steps

STEP 6: Attach Headboard/Bed Side Rails and Staircase

Connect headboards, side rails, and staircase components using specified hardware.

STEP 7: Attach Slats

Install the bed slats securely to the frame, following specific attachment instructions.

STEP 7 WARNING

Crucial warning about securing both sides of each slat to prevent injury and voiding warranty.

STEP 8: Attach Guard Rails

Install the guard rails on the upper bunk for added safety and fall prevention.

STEP 9: Slide Toy Box into Place

Position the loft bed in its final location and insert the toy box.

Care and Maintenance

CARE INSTRUCTIONS

Guidance on cleaning and protecting the furniture's finish without damage.

Wood Properties and Environment

Information on natural wood variations, expansion, and avoiding damaging environmental factors.

Warranty Information

WRITTEN LIMITED WARRANTY

Details the 1-year warranty against defects in material or workmanship.

WARRANTY LIMITATIONS AND EXCLUSIONS

Outlines conditions, exclusions, and limitations of the product warranty.

Claims and Other Provisions

Procedure for warranty claims and disclaimers of other implied warranties.