Hitachi CP-X3030WN User Manual

79
SECURITY menu
(continued on next page)
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table
below can be performed.
To use SECURITY menu: User registration is required
before using the security functions.
Enter to the SECURITY menu
1. Press the ► button. The ENTER PASSWORD box will be displayed.
2. Use the ▲/▼/◄/► buttons to enter the registered password.
The factory default password is as follows.
This password can be changed
(

below)
. Move the cursor to
the right side of the ENTER PASSWORD box and press
the ► button to display the SECURITY menu.
• It is strongly recommended the factory default password to be
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box
will be displayed again. If incorrect password is input 3 times, the
projector will turn off. Afterwards the projector will turn off every time
an incorrect password is input.
3. Items shown in the table below can be performed.
If you have forgotten your password
(1) While the ENTER PASSWORD box is displayed, press and hold the
RESET button on the remote control for about 3 seconds or press
and hold the INPUT button for 3 seconds while pressing the ►
button on the projector.
(2) The 10 digit Inquiring Code will be displayed. Contact your dealer
with the 10 digit Inquiring Code. Your password will be sent after your user registration information
is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will
close. If necessary, repeat the process from (1).
Item Description
SECURITY
PASSWORD
CHANGE
(1) Use the ▲/▼ buttons on the SECURITY menu
to select SECURITY PASSWORD CHANGE
and press the ► button to display the ENTER
NEW PASSWORD box.
(2) Use the ▲/▼/◄/► buttons to enter the new password.
(3) Move the cursor to the right side of the ENTER
NEW PASSWORD box and press the ► button
to display the NEW PASSWORD AGAIN box,
enter the same password again.
(4)
Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press the ►
button and the NOTE NEW PASSWORD box
will be displayed for about 30 seconds, please
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
SECURITY menu
CP-X2530WN, CP-X3030WN : 8112
CP-WX3030WN : 2510

Hitachi CP-X3030WN Specifications

General

Number of colors	16.78 million colors
Native aspect ratio	4:3
Projection distance	- m
Projection technology	3LCD
Supported aspect ratios	4:3, 16:9, 16:10
Contrast ratio (typical)	4000:1
Screen size compatibility	30 - 300 \
Projection distance (tele)	1 - 10.8 m
Projection distance (wide)	0.8 - 9 m
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	-30 - 30 °
Horizontal synchronization (max)	106 kHz
Horizontal synchronization (min)	31.5 kHz
Projector brightness (economic mode)	2100 ANSI lumens
Focus	Manual
Zoom capability	Yes
Focal length range	- mm
Lamp type	UHP
Lamp power	215 W
Light source type	Lamp
Service life of light source	5000 h
Service life of light source (economic mode)	6000 h
Full HD	No
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
RMS rated power	16 W
Number of built-in speakers	1
Built-in display	-
HDMI version	1.4
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	3
Noise level	38 dB
Certification	UL60950-1/cUL, FCC Part 15 subpart B class B, CE Marking: EN61000-3-2, EN61000-3-3, EN55022, EN55024 (EMC Directive), EN60950-1 (Low voltage directive), WEEE, RoHS, ErP (lot6) compliant, c-tick class B
Noise level (economic mode)	30 dB
Placement	Desktop
Product type	Standard throw projector
Product color	White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	310 W

Weight and Dimensions

Depth	245 mm
Width	320 mm
Height	85 mm
Weight	3000 g