Need help?Do you have a question about the Holder C Series and is the answer not in the manual?
Information on potential discrepancies between the manual and the vehicle due to ongoing development.
Contact details for Max Holder GmbH for inquiries about the vehicle.
Specifies the suitable applications for the vehicle and any restrictions.
Details on where the vehicle can be operated, including public streets.
Highlights inherent risks even with permitted use and the need for vigilance.
Guidance on the proper disposal of vehicle materials according to regulations.
Details required driving permits based on vehicle speed and weight.
Table outlining driving permit classes for agricultural and forestry tractors.
Essential safety regulations to observe for safe operation and emergency procedures.
Recommendations for appropriate work clothing to prevent entanglement.
Details on exhaust gas components and their toxic properties.
Warning about explosion risk from battery gases (hydrogen/oxygen mixture).
Warning about fire risk from hot exhaust gases igniting combustible materials.
Description of cab classification standards and categories relevant to driver protection.
Detailed dimensional drawings and measurements for C250 and C270 models.
Diagram identifying key components visible from the front left of the vehicle.
Identification of controls located behind the seat and on the console for C350/C370.
Identification of window operating mechanisms on the left and right sides.
Advice regarding steering angles and their impact on emergency door access.
Instructions for pre-start checks, emphasizing safety and ensuring vehicle operability.
Steps for detaching attachments and raising the hydraulic tipping system.
Procedure for detaching attachments and manually lifting/securing the body frame.
Procedure for checking vehicle lighting and rear-view mirrors for proper function.
Instructions for adjusting the steering column's height and inclination for comfortable operation.
General advice on adjusting seats for safe and comfortable reach of all controls.
Procedure for adjusting weight settings on mechanically sprung seats using the display and lever.
How to adjust the seat position forward or backward using a lever.
Instructions for enabling or disabling horizontal suspension for the driver's seat.
Instructions for adjusting the armrest position using a wheel for optimal comfort.
Procedure for shutting down the engine by turning the ignition key.
Procedure for checking the proper functioning of steering and braking systems before driving.
Essential pre-drive checks and safety rules, including traffic laws and load considerations.
Step-by-step guide for correctly fastening the safety belt.
Guidance on operating the direction switch and changing travel direction safely.
Explanation of the two-stage steering system for road and working operations.
Procedure for applying and releasing the service brake using the brake pedal.
Instructions for engaging and disengaging the parking brake using the switch.
Procedure for engaging the differential lock, including indicator lights and signal tone.
Procedure for disengaging the differential lock.
Steps to activate parking lights and associated indicator lamps.
Procedure to switch on the dipped beam headlights and related indicators.
Steps to activate the high beam headlights, including lever and indicator positions.
Procedure for signalling a right turn using the flasher lever.
Procedure for signalling a left turn using the flasher lever.
How to operate the vehicle's signal horn.
Advice on operating the radio, emphasizing the need to read its manual.
Procedure for unhinging the cab roof hatch for use as an emergency exit.
Recommendations for operating the vehicle in winter conditions, including fuel, oil, and hydraulics.
Instructions for using the coolant preheating system in very cold temperatures.
Guidance on using winter diesel fuel at low temperatures.
Recommendations for using appropriate motor oils during winter operation.
Advice on operating hydraulics in cold conditions and bringing them to temperature.
Recommendation to use window washing water with anti-freeze in sub-zero temperatures.
Information on equipping tyres with snow chains for improved traction.
Procedure for setting up the vehicle for stationary operation, including PTO shaft engagement.
Advice on selecting and using tested and approved attachments, recommending customer service consultation.
List of common attachments compatible with the vehicle.
Information on the approval status of front and rear loaders for the C series.
Crucial safety rules for securely parking and attaching equipment to prevent roll-away.
Guidance on calculating gross weight, axle loads, and tyre capacity for proper ballasting.
Procedure for switching hydraulic functions on and off using the master switch.
Steps to stop the vehicle, lower attachments, set brakes, and prepare for shutdown.
Procedure for driving the vehicle onto transport and securing it.
Critical DANGER warnings regarding swinging loads and proper lifting gear usage during loading.
Overview of potential notifications and signal tones from the multifunction display or signal tone generator.
Emphasis on conscientious handling and care of the vehicle to ensure availability.
Information on customer service, regular maintenance by dealers, and warranty claims.
Requirements for personnel performing maintenance and repair work, emphasizing hazard awareness.
Rules for performing maintenance safely, including stationary operation and hazard zones.
Instructions for applying protective wax to the vehicle to prevent corrosion.
Instructions for securing the raised cargo bed sub-frame to prevent inadvertent lowering.
Procedure for checking V-belts for cracks, tension, and condition, including replacement advice.
General advice for user maintenance tasks, including electrical system safety and light bulb replacement.
Steps for preparing the vehicle for extended storage, including cleaning and lubrication.
Procedure for preserving the engine during extended shutdown, including oil changes and sealing openings.
Steps for preparing and starting the vehicle after a shutdown period.
Specific checks to perform during vehicle startup, focusing on hydraulics, steering, and brakes.
Detailed list of fluids and lubricants, their specifications, viscosity grades, and seasonal use.
Specific tightening torques for steering, hydraulic valves, and wheel nuts.
Reference to the service manual for engine tightening torques.
Initial maintenance checks and tasks to be performed after the first few operating hours or at vehicle handover.
General| Brand | Holder |
|---|---|
| Model | C Series |
| Category | Utility Vehicle |
| Language | English |
To Next Page
