EasyManua.ls Logo

Holland FWS1 Series - User Manual

Holland FWS1 Series
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
XL-FW10054UM-en-US Rev C
Owner’s Manual
FWS1 and FWS2 Series Fifth Wheels
Operation, Maintenance and
Troubleshooting Procedures
FWS1 Assembly Series
XA-S1 Top Plate Series
FWS2 Assembly Series
XA-S2 Top Plate Series

Table of Contents

Questions and Answers

  • J
    Justin MillerAug 11, 2025
    Why is it so difficult to couple my Holland FWS1 Accessories to the trailer?
    • D
      Daniel ClarkeAug 11, 2025
      Difficulty in coupling to a trailer can arise from several factors. You might be trying to couple too quickly, so ensure you follow the correct procedure as described in this Owner’s Manual. The trailer could be too high, preventing the kingpin from properly entering the lock; if so, lower it according to the manufacturer's instructions. The lock may be closed, in which case you should manually pull the release handle out fully and swing the hinged lock open, or if air release equipped, set tractor brakes and actuate fifth wheel control valve to open lock.
  • R
    rowlandjoseAug 17, 2025
    What to do if it's hard to couple Holland FWS1 Accessories to the trailer?
    • S
      Suzanne FranklinAug 17, 2025
      If you're finding it hard to couple your Holland Accessories to the trailer, accumulated rust or grime might be interfering with the lock's operation. Try thoroughly cleaning the fifth wheel and re-lubricating it as described in this Owner’s Manual. Alternatively, the lock might be adjusted too tightly; check the lock adjustments according to the procedure in this Owner’s Manual.
  • J
    Jesse SharpAug 23, 2025
    What to do if Holland FWS1 Accessories are difficult to couple due to lock or handle issues?
    • S
      sandra95Aug 23, 2025
      If you're having trouble coupling your Holland Accessories to a trailer, the lock might be damaged, and the fifth wheel MUST be rebuilt using the appropriate SAF-HOLLAND service kit. Another cause could be a damaged or bent release handle, which would need replacing using the appropriate SAF-HOLLAND service kit. A jammed safety indicator could also be the culprit; inspect the release handle, and if it’s bent, replace it using the appropriate SAF-HOLLAND service kit.
  • L
    Luke NelsonAug 29, 2025
    What to do if Holland FWS1 are difficult to couple because of damage to the lock jaw or top plate?
    • B
      bwhiteAug 30, 2025
      If you're experiencing difficulty coupling your Holland Accessories to the trailer, it's possible that the lock jaw opening is spread due to a prior high coupling attempt. Measure the width of the opening in the jaw. If it's greater than 2.38 inches, replace it using the appropriate SAF-HOLLAND service kit. Also, a damaged top plate just below the lock adjustment pin could be the issue, in which case the entire fifth wheel top plate MUST be replaced.
  • A
    apopeSep 4, 2025
    How to troubleshoot coupling issues with Holland FWS1 Accessories related to the kingpin or lube plate?
    • J
      Justin YoungSep 4, 2025
      If you're having trouble coupling your Holland Accessories to the trailer, a bent kingpin, damaged upper coupler, or improper use of a “lube plate” may be interfering with lock movement. You should check the kingpin and upper coupler as detailed in HOLLAND Service Bulletin XL-SB020 and repair or replace them as needed. Also, remove any improperly installed or specified lube plates, and refer to HOLLAND Service Bulletin XL-SB004-01 for lube plate warnings.

Holland FWS1 Series Specifications

General IconGeneral
TypeFlow Switch
SeriesFWS1
Switch TypeSPDT
Body MaterialBrass
Temperature Range-20°F to 180°F