EasyManua.ls Logo

Holmes HM630 Series - User Manual

Holmes HM630 Series
8 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
When not using your humidifier for an extended period of time:
1. Dispose of the filters. DO NOT leave in unit.
2. Clean, rinse and thoroughly dry the humidifier as directed in weekly maintenance. DO NOT leave any water in
the unit when storing. Leaving water in the unit may render the unit inoperable for the following season.
3. Place the humidifier in the original carton and store in a cool, dry place.
4. Order your replacement filter for next year’s use.
WEEKLY MAINTENANCE / STORAGE INSTRUCTIONS
REPLACEMENT ACCESSORIES
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
WARRANTY INFORMATION
© 2014 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
162385 REV A HM630 Series_14EM1 Printed in China
GCDS-HOL36708-BB
Owner’s Guide
HM630 Series
TROUBLESHOOTING
FREQUENTLY ASKED QUESTIONS
Cool Mist Tower
Humidifier
REPLACEMENT ACCESSORIES
To order the replacement accessories you can do any of the following:
Visit your local retailer
Go to www.holmesproducts.com
Call consumer service at 1-800-546-5637
FREQUENTLY ASKED QUESTIONS
QUESTIONS ANSWER
The estimated run time for this humidifier is based on average room conditions. The
actual run time of your humidifier is dependent on numerous variables such as:
1. Air exchange in the room where the humidifier is placed.
2. Room construction where the humidifier is placed.
3. Temperature of the room where the humidifier is placed.
4. Humidity levels in the room where the humidifier is placed.
5. Movement of occupants and the opening and closing of doors in the room
where the humidifier is placed.
6. Home furnishings in the room where the humidifier is placed.
See Daily Maintenance instructions. Regular cleaning is recommended.
1. Run your unit on the lowest setting.
2. If your unit has electronics, set it to your desired humidity level. The unit will
turn on and off, which will extend the run time.
3. Fill the tank all the way full, place it on the base, let the water empty into
the base until it stops bubbling, then refill the tank full again. This ensures
maximum water capacity and will extend run time.
What are the variables that
affect run time?
How do I remove film on
water tank?
How can I extend the run
time?
INFO HOT-LINE: If, after reading this owner’s guide you have
any questions or comments, please call 1-800-546-5637 and a
Customer Service Representative will be happy to assist you.
FILTER #: HWF100-UC2/HWF100(2)
FILTER TYPE: WICK
WEEKLY MAINTENANCE
To Remove Scale:
1. Repeat steps 1-4 (refer to DAILY MAINTENANCE).
2. Clean the base by partially filling the base with one 8-oz cups of undiluted white vinegar, or by using
Cleanse Clean
®
solution (Model S1710) made by the manufacturer. Leave this solution in the base for 20
minutes, while cleaning the all interior surfaces with a soft brush. Remove base scale by wiping the base with a
cloth dampened with undiluted white vinegar.
3. Rinse with clean warm water to remove the cleaning solution before disinfecting the tank.
To Disinfect Humidifier Base and Tank:
1. Fill humidifier tank 1/2 full with water and 1/2 tablespoon of chlorine bleach.
2. Let the solution stand for 20 minutes, swishing every few minutes. Wet all surfaces.
3. Carefully empty the tank after 20 minutes, and rinse with warm water until you can not detect any bleach smell.
Dry with a clean cloth or paper towel.
4. Place filter back into tank and refill the water tank as directed in Operating Instructions, and turn the unit on.
STORAGE INSTRUCTIONS
3 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited
doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of 3 years from the date of
purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this
product or any component of the product found to be defective during the warranty period. Replacement will be made with a
new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar
product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or
mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the
original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail
stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of
the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by
anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire,
flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory
warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a
particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the
product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract,
fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to
state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding this warranty or would like to obtain warranty service, please call 1-800-546-5637 and a
convenient service center address will be provided to you.
In Canada
If you have any question regarding this warranty or would like to obtain warranty service, please call 1-800-546-5637 and a
convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca
Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden
Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in
connection with this product, please write our Consumer Service Department. PLEASE DO NOT RETURN THIS PRODUCT
TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
If you have any questions regarding your product or would like to learn more about other Sunbeam
®
products, please
contact our Consumer Service Department at 1-888-264-9669 or visit our website at www.sunbeam.com. For inquiries
regarding recycling and proper disposal of this product, please contact your local waste management facility.
TROUBLE
Unit does not turn on
Mist output minimal to none
Filter turns brown
Filter Check
®
Indicator is not working
Humidifier continuously displays 21%
Humidifier continuously displays 90%
PROBABLE CAUSE
Not plugged in
Mist is invisible. The filter has not
absorbed water
The filter has absorbed minerals
Takes 30 minutes to register
Humidity at the humidifier is at or
below 21%
Humidity at the humidifier is at or
above 90%
SOLUTION
Plug in unit
Wait 30 minutes for filter to absorb
water
Replace your filter (HWF100- UC2
/HWF100) by calling
1-800-546-5637, or visiting
www.holmesproducts.com
Allow the humidifier to run
continuously for 30 minutes for the
FilterCheck
®
Indicator to reflect the
filter condition
Continue to operate humidifier to raise
the room humidity
Stop operating the humidifier if the
humidity level is too high
HM630 Series_14EM1.qxd:HM630/630RC08EM2 5/7/15 4:57 PM Page 1
Question and Answer IconNeed help?

Do you have a question about the Holmes HM630 Series and is the answer not in the manual?

Summary

Important Safety Instructions

General Safety Precautions

Key safety guidelines to reduce fire, shock, and injury risks when using the appliance.

Polarized Plug Safety

Information regarding the polarized plug and electrical safety standards for operation.

Humidifier Features and Operations

How Cool Mist Works

Explains the process of drawing air through a wick filter to produce moist air.

Pre-Operating and Filling

Steps for initial setup, location selection, and filling the water tank.

Operating Modes

Details on using manual settings and the AccuSet Plus Digital Humidistat for humidity control.

Timer Functions

Instructions for using the Auto On/Off timer feature to schedule operation.

Cleaning and Maintenance

Filter Replacement and Indicator

Procedure for replacing the wick filter and understanding the FilterCheck® indicator.

Daily Cleaning Procedures

Essential daily steps to maintain the humidifier's cleanliness and prevent build-up.

Troubleshooting and FAQs

Troubleshooting Guide

Solutions for common operational problems and issues encountered with the humidifier.

Frequently Asked Questions

Answers to common user inquiries regarding humidifier performance and extended use.

Warranty Information

3 Year Limited Warranty Details

Overview of the warranty coverage, limitations, and terms.

Obtaining Warranty Service

Instructions for contacting customer service for repair or replacement.

Weekly Maintenance, Storage, and Accessories

Weekly Cleaning and Disinfection

Guidelines for weekly maintenance, scale removal, and disinfecting the unit.

Storage Instructions

Steps for proper cleaning and storing the humidifier for extended periods.

Replacement Accessories

Information on how to order replacement filters and other accessories for the humidifier.

Overview

The Holmes HM630 Series Cool Mist Tower Humidifier is designed to add invisible moisture to dry indoor air, improving comfort and health. This appliance utilizes a cool mist humidification system, drawing dry air through a rear air intake grill and passing it through a moisture-laden wick filter. This filter retains minerals and deposits from the water, and the resulting moist air is then directed back into the room from the top air grill. It's important to note that the moisture output is invisible, so it's normal not to see a visible mist. The recommended humidity level for optimal comfort and health is between 40% and 50%.

Important Safety Instructions:

Before operating the humidifier, users must read and save all important safety instructions to reduce the risk of fire, electric shock, and injury. The appliance should be plugged directly into a 120V AC electrical outlet. The cord must be kept out of heavy traffic areas and never placed under rugs or near heat registers. The humidifier should not be placed near heat sources like stoves, radiators, or heaters, but rather on an inside wall, at least 4 inches (10 cm) away from the wall for best results. It should never be placed in an area accessible to children or in a closed room where a child may be sleeping, resting, or playing, as this can lead to excessive humidity.

Users are warned not to attempt to refill the humidifier without first unplugging it from the electrical outlet. The unit should never be tilted, moved, or emptied while operating. It should be shut off and unplugged before removing the water tank or moving the unit. Nothing should ever be placed over the moisture outlet while the unit is running, and no objects should be dropped or inserted into any openings. The appliance should not be operated with a damaged cord or plug, or if it has malfunctioned, been dropped, or damaged. In such cases, it should be returned to the manufacturer for examination, adjustment, or repair.

The humidifier is intended for household use only, and any other use not recommended by the manufacturer may cause fire, electric shock, or injury. Attachments not recommended or sold by the manufacturer should not be used. The unit is not designed for outdoor use. It must always be placed on a firm, flat, level surface, and a waterproof mat or pad is recommended underneath. It should never be placed on a rug, carpet, or a finished floor that could be damaged by water or moisture. The moisture outlet should not directly face a wall, as this could cause damage, especially to wallpaper. The humidifier should be unplugged when not in use.

Daily and weekly maintenance is required for appropriate operation. Only cleaners and additives recommended by the manufacturer should be used. Detergents, gasoline, glass cleaner, furniture polish, paint thinner, or other household solvents should never be used to clean any part of the humidifier. If excessive humidity causes water condensation on windows and furniture, the humidifier should be turned OFF. The humidifier should not be used in areas where humidity levels exceed 50%; a hygrometer can be used to measure humidity. Users should not attempt to repair or adjust any electrical or mechanical functions, as this will void the warranty. The unit contains no user-serviceable parts, and all servicing should be performed by qualified personnel. The housing should never be placed under water flow or immersed in liquids.

The appliance features a polarized plug (one blade wider than the other) to reduce the risk of electric shock. This plug is designed to fit into a polarized outlet only one way. If it doesn't fit fully, the plug should be reversed. If it still doesn't fit, a qualified electrician should be contacted to install the proper outlet. Users should not attempt to modify the plug or defeat this safety feature.

Pre-Operating Instructions:

Before use, ensure the humidifier is switched to OFF and disconnected from the electrical outlet. Select a flat surface location, about 4 inches (10 cm) away from the wall. Avoid placing it on finished floors or near furniture that could be damaged by moisture. A moisture-resistant surface is recommended.

Filling the Water Tank:

  1. Remove the tank from the humidifier housing by grabbing the handle and pulling forward. Lift the tank out and bring it to a faucet.
  2. Turn the tank upside down and twist off the tank cap counter-clockwise.
  3. Fill the tank with cool, fresh tap water. Do NOT use warm water, as this may cause leaking.
  4. Replace the cap on the tank FIRMLY.
  5. Carry the full tank back to the humidifier and place it into the housing, aligning it with the locating tab on the tank base. The tank holds 1.2 gallons of water and will immediately begin to empty into the base.
  6. Plug the power cord into a 120V AC electrical outlet.

Operating Instructions:

The HM630 Series humidifier is equipped with an AccuSet Plus™ Digital Humidistat, allowing users to run it continuously in manual mode or set a desired humidity level between 30% and 65% relative humidity. The humidistat automatically turns the humidifier ON or OFF based on the preset comfort level.

Manual Mode Instructions:

  1. Plug the humidifier into a 120V AC electrical outlet. The display will show the current room humidity.
  2. The display range is 21% - 90%. If room humidity is below 21%, the display shows "21". If it's above 90%, it shows "90".
  3. To start the unit, push the power button twice within 3 seconds for the HIGH (3) manual setting.
  4. Press the power button again for MEDIUM (2) and again for LOW (1). After selection, the display returns to current room humidity.
  5. To stop the unit, press and hold the power button for two seconds, or keep pressing until the display reads OFF (OF).

AccuSet Plus™ Humidistat Instructions:

To use the AccuSet Plus™ Digital Humidistat, press the power button until the speed is set to AUTO HIGH (A3), AUTO MEDIUM (A2), or AUTO LOW (A1). Adjust the set humidity using the up and down buttons, increasing or decreasing in 5% increments. Once set, the display returns to current room humidity. The humidifier will stop if room humidity rises above the set level and turn on automatically if it drops below the set level. Allow up to 30 minutes for the filter to fully absorb water and for the unit to produce moisture. The AccuSet Plus™ Humidifier has memory, so it will return to the last setting when turned back on. If the humidifier won't be used for two or more days, drain all residual water from the tank, base, and wick filter to prevent algae or bacteria growth.

Hour Auto On/Off Timer Instructions:

The Auto On/Off timer offers two options: setting a time to turn the unit off or setting a time to turn it on.

Auto Off Timer:

While the unit is running, activate the off timer by holding down the up and down buttons simultaneously for 2 seconds. The screen will flash "00". Use the up and down arrows to adjust the timer up to 16 hours in 1-hour increments. After 16 hours, the next push cycles back to "00" hours. An LED indicates the timer is on. The unit will shut off after the timer expires. The timer will shut off if other modes are changed. It should only be deactivated if the unit is turned off.

Auto On Timer:

While the unit is off, press the up and down buttons simultaneously for 2 seconds. The display will flash "00". The up button can then be pushed to increase the hours to turn on (in its last setting) from 1-16 hours in 1-hour increments. The unit will come on after the timer expires. If the unit is then turned on, the timer will be deactivated. An LED indicates the timer is activated. After 16 hours, the next push cycles back to "00" hours. The Auto On Timer only activates when the room humidity is below 30%.

Replacing the Filters:

Over time, waterborne minerals and sediment become trapped in the wick filter. The harder the water, the more frequently the filter will need to be changed. The FilterCheck® Indicator monitors filter life. After 30 minutes of use, the FilterCheck® Indicator will move to show filter condition. A new filter will register in the "GOOD filter" section. After frequent use, the indicator will show when filters need to be changed (see Figure 2). When the needle is in the "CHANGE" section, it means insufficient moisture is entering the air due to excessive minerals and sediment on the filters, and the filter should be replaced to maintain stated performance.

To replace the filter:

  1. Turn the unit off and disconnect from the electrical outlet.
  2. Remove the tank from the housing.
  3. Unlock the housing from the base by turning the lock knob to the unlocked position.
  4. Lift the housing straight up and place it aside.
  5. Unlock the wick holder from the base by turning the lock knob to the unlocked position.
  6. Remove the old wicks from the wick holder.
  7. Follow the weekly cleaning instructions (see below).
  8. Insert new filters into the wick holder and lock the wick holder back onto the base.
  9. Replace the housing onto the base and lock it into place.
  10. Fill the tank and place it back into the housing.
  11. Repeat Operating Instructions. It will take about 30 minutes for the humidifier to reach maximum output.

Replacement filters (model HWF100-UC2/HWF100 – 2 filters) can be purchased from local retailers, by calling 1-800-546-5637, or by visiting www.holmesproducts.com. It is recommended to have a replacement filter for uninterrupted use.

Cleaning and Maintenance Instructions:

Proper maintenance and cleaning are essential for the humidifier's continued performance and to prevent algae or bacteria build-up.

Daily Maintenance:

  1. Ensure the unit is OFF and disconnected from the electrical outlet.
  2. Remove the housing and the tank from the humidifier and place them in a sink or tub.
  3. Carry the base to the sink, remove the wick, drain any remaining water, and rinse thoroughly to remove sediment or dirt. Wipe clean and dry with a clean cloth or paper towel.
  4. Drain the water from the tank into the sink and rinse thoroughly. Wipe clean and dry with a clean cloth or paper towel.
  5. Put filters back into the wick holder, ensuring the rivet attaches to the holder. Lock the wick holder back into place. Replace the housing and lock it into place. Refill the tank with cool tap water as instructed in the filling instructions. Do not overfill.
  6. Follow Operating Instructions. NOTE: The tray is dishwasher safe (TOP RACK ONLY) for easy cleaning.

Weekly Maintenance (To Remove Scale):

  1. Repeat steps 1-4 of Daily Maintenance.
  2. Clean the base by partially filling it with one 8-oz cup of undiluted white vinegar, or by using Cleanse Clean® solution (Model S1710) made by the manufacturer. Leave this solution in the base for 20 minutes, while cleaning all interior surfaces with a soft brush. Remove base scale by wiping the base with a cloth dampened with undiluted white vinegar.
  3. Rinse with clean warm water to remove the cleaning solution before disinfecting the tank.

To Disinfect Humidifier Base and Tank:

  1. Fill the humidifier tank 1/2 full with water and 1/2 tablespoon of chlorine bleach.
  2. Let the solution stand for 20 minutes, swishing every few minutes to wet all surfaces.
  3. Carefully empty the tank after 20 minutes and rinse with warm water until no bleach smell is detected. Dry with a clean cloth or paper towel.
  4. Place the filter back into the tank and refill the water tank as directed in Operating Instructions, then turn the unit on.

Storage Instructions:

When not using the humidifier for an extended period:

  1. Dispose of the filters. Do NOT leave them in the unit.
  2. Clean, rinse, and thoroughly dry the humidifier as directed in weekly maintenance. Do NOT leave any water in the unit when storing, as this may render it inoperable for the following season.
  3. Place the humidifier in its original carton and store it in a cool, dry place.
  4. Order a replacement filter for next year's use.

Replacement Accessories:

To order replacement accessories:

  • Visit your local retailer.
  • Go to www.holmesproducts.com.
  • Call consumer service at 1-800-546-5637.

For questions about the product or other Sunbeam® products, contact the Consumer Service Department at 1-888-264-9669 or visit www.sunbeam.com. For recycling and disposal inquiries, contact your local waste management facility.

Troubleshooting:

  • Unit does not turn on: Probable cause is not plugged in. Solution: Plug in unit.
  • Mist output minimal to none: Probable cause is that mist is invisible and the filter has not absorbed water. Solution: Wait 30 minutes for the filter to absorb water.
  • Filter turns brown: Probable cause is that the filter has absorbed minerals. Solution: Replace your filter (HWF100-UC2/HWF100) by calling 1-800-546-5637 or visiting www.holmesproducts.com.
  • Filter Check® Indicator is not working: Probable cause is that it takes 30 minutes to register. Solution: Allow the humidifier to run continuously for 30 minutes for the FilterCheck® Indicator to reflect the filter condition.
  • Humidifier continuously displays 21%: Probable cause is that humidity at the humidifier is at or below 21%. Solution: Continue to operate the humidifier to raise the room humidity.
  • Humidifier continuously displays 90%: Probable cause is that humidity at the humidifier is at or above 90%. Solution: Stop operating the humidifier if the humidity level is too high.

Frequently Asked Questions:

  • What are the variables that affect run time? The estimated run time is based on average room conditions. Actual run time depends on:
    1. Air exchange in the room.
    2. Room construction.
    3. Room temperature.
    4. Humidity levels in the room.
    5. Movement of occupants and opening/closing of doors.
    6. Home furnishings in the room.
  • How do I remove film on water tank? See Daily Maintenance instructions. Regular cleaning is recommended.
  • How can I extend the run time?
    1. Run your unit on the lowest setting.
    2. If your unit has electronics, set it to your desired humidity level. The unit will turn on and off, extending run time.
    3. Fill the tank completely, place it on the base, let the water empty into the base until bubbling stops, then refill the tank fully again. This ensures maximum water capacity and extends run time.

Warranty Information:

The Holmes HM630 Series Humidifier comes with a 3-year limited warranty from Sunbeam Products, Inc. (Jarden Consumer Solutions or JCS in Canada). JCS warrants that the product will be free from defects in material and workmanship for 3 years from the purchase date. JCS will repair or replace defective products or components at its option. Replacement may be with a new or remanufactured product of equal or greater value. This is the exclusive warranty, and users should not attempt to repair or adjust electrical or mechanical functions, as this will void the warranty.

The warranty is valid for the original retail purchaser and is not transferable. The original sales receipt is required for proof of purchase. JCS dealers, service centers, or retail stores cannot alter the terms of this warranty. The warranty does not cover normal wear of parts or damage from negligent use, misuse, improper voltage/current, use contrary to instructions, disassembly, repair, or alteration by unauthorized parties. It also does not cover Acts of God (fire, flood, hurricanes, tornadoes).

Limits on JCS's Liability:

JCS is not liable for incidental or consequential damages caused by breach of warranty. Except where prohibited by law, any implied warranty of merchantability or fitness for a particular purpose is limited to the duration of the express warranty. JCS disclaims all other warranties, conditions, or representations. JCS is not liable for damages of any kind resulting from purchase, use, misuse, or inability to use the product, including incidental, special, consequential, or similar damages, loss of profits, or for any breach of contract or claim brought by another party. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on implied warranties, so these limitations may not apply. This warranty provides specific legal rights, and you may have other rights that vary by jurisdiction.

How to Obtain Warranty Service:

  • In the U.S.A.: For questions or warranty service, call 1-800-546-5637. A convenient service center address will be provided.
  • In Canada: For questions or warranty service, call 1-800-546-5637. A convenient service center address will be provided.

In the U.S.A., the warranty is offered by Sunbeam Products, Inc. (Jarden Consumer Solutions) located in Boca Raton, Florida 33431. In Canada, it's offered by Sunbeam Corporation (Canada) Limited (Jarden Consumer Solutions) located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. Do NOT return this product to these addresses or to the place of purchase.

Holmes HM630 Series Specifications

General IconGeneral
BrandHolmes
ModelHM630 Series
CategoryHumidifier
LanguageEnglish

Related product manuals