HOLT 57056 - Maintenance and Troubleshooting; Inspection and Daily Maintenance; Troubleshooting Common Problems

Page 13;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1Item 57056
EF;6GHIJ6KFGLIMNFLMG6MFMO6 E6GPJ
L8#/*4$"&8=%N,"8$*8,84*=%,89%O7*,8"83
%J(&4*9'(*#%8&$%#/*4"2"4,77V%*Z/7,"8*9%"8%$."#%5,8',7%5'#$%
+*%/*(2&(5*9%&87V%+V%,%<',7"2"*9%$*4.8"4",81
GI%JK6!6MG%E6KLIPE%LMfPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%&22%$.*%$&&7=%9*$,4.%$.*%,"(%#'//7V=%#,2*7V%9"#4.,(3*%,8V%(*#"9',7%,"(%/(*##'(*%
"8%$.*%$&&7=%,89%(*7*,#*%$.*%$.(&$$7*%,890&(%$'(8%$.*%#)"$4.%$&%"$#%&22%/&#"$"&8%+*2&(*%
/*(2&(5"83%,8V%"8#/*4$"&8=%5,"8$*8,84*=%&(%47*,8"83%/(&4*9'(*#1
GI%JK6!6MG%E6KLIPE%LMfPKH%;KIN%GIIT%;FLTPK6-%
U&%8&$%'#*%9,5,3*9%*<'"/5*8$1%%L2%,+8&(5,7%8&"#*=%Y"+(,$"&8=%
&(%7*,W"83%,"(%&44'(#=%.,Y*%$.*%/(&+7*5%4&((*4$*9%+*2&(*%2'($.*(%'#*1
;&77&)%,77%3'"9*7"8*#%(*3,(9"83%5,$*(",7#%+*"83%*Z$(,4$*9=%%
"847'9"83%NEUE%"8#$('4$"&8#%,89%6JF%(*3'7,$"&8#1%
M&$*- These procedures are in addition to the regular checks and maintenance
explained as part of the regular operation of the air-operated tool.
1. S6;IK6%6FO[%PE6= inspect the general
condition of the Fluid Extractor. Check for:
• loose hardware or housing
• misalignment or binding of moving parts
• cracked or broken parts
• any other condition that may
affect its safe operation.
2. U,"7V%?%F"(%E'//7V%N,"8$*8,84*-%
Every day, maintain the air supply according
to the component manufacturers' instructions.
Drain the moisture filter regularly.
Performing routine air supply maintenance
will allow the tool to operate more safely
and will also reduce wear on the tool.
3. Clean external surfaces of the tool with a
clean, dry cloth. Clean the Reservoir Tank
with compatible solvent that will not damage
it to remove accumulated debris. Dispose of
solvent properly and allow Reservoir Tank to
air dry completely. Do not allow solvent to sit
in Reservoir Tank for an extended period.
4. Store the Fluid Extractor in a safe, dry,
clean location out of reach of children.
G(&'+7*#.&&$"83
J(&+7*5 J&##"+7*%O,'#*# T"W*7V%E&7'$"&8#
Unit does not extract fluid 1. Extracting Tube detached.
2. Extracting Tube not
positioned properly.
3. All fluid has been removed.
1. Reattach Extracting Tube.
2. Firmly insert Extracting Tube
into correct location.
3. Verify there is still fluid to be removed.
Decreased suction or
tubes leaking fluid
Holes/cracks in tubes. Check all suction/extraction tubes for
cracks. Replace any defective tubes with
new tubes. Do not repair old tubes.
;&77&)%,77%#,2*$V%/(*4,'$"&8#%).*8*Y*(%9",38&#"83%&(%#*(Y"4"83%$.*%;7'"9%6Z$(,4$&(1%