HOLZMANN MASCHINEN BS 712TOP

Questions and Answers

J
John TaylorAug 2, 2025
What to do if HOLZMANN MASCHINEN BS 712TOP does not start?
- C
  Christopher SnyderAug 2, 2025
  If your HOLZMANN MASCHINEN Saw doesn't start, several factors could be at play. First, check all power connections to ensure the machine is properly connected to the power supply. If the connections are secure, inspect the fuse of the power circuit; a defect or unsuitable fuse can prevent the machine from starting, so replace it if necessary. Lastly, a defective cable could be the culprit, in which case you should replace the cable.
J
Jacqueline HesterAug 8, 2025
Why HOLZMANN MASCHINEN BS 712TOP band does not come to full speed?
- T
  Teresa DennisAug 8, 2025
  If the saw band on your HOLZMANN MASCHINEN Saw isn't reaching full speed and seems to lack power, consider these potential causes: the extension cord might be too long, so change to a suitable extension cord with sufficient cross-section, insulation and length. Also, the power supply may not match the motor's requirements, it is best to have it checked by an electrician. A weak or unstable power supply can also cause this issue; in this case, contact your electric power company.
E
emilycaldwellAug 12, 2025
What to do if HOLZMANN MASCHINEN Saw makes bad cuts?
- R
  rodgersjulieAug 12, 2025
  If your HOLZMANN MASCHINEN Saw is producing bad cuts, several factors could be responsible. The descent velocity might be too high, so reduce it. The saw band might be unsuitable for the material you're cutting; for example, use HQ Bi-Metal bands for stainless steel. A worn saw band will also cause poor cuts, so replace it. Ensure the saw band is correctly tensioned. Finally, the saw band guide might be out of balance, so readjust it.
G
greenelisaAug 18, 2025
Why HOLZMANN MASCHINEN BS 712TOP Saw motor gets hot quickly?
- E
  Elizabeth GallagherAug 18, 2025
  If the motor of your HOLZMANN MASCHINEN Saw gets hot very quickly and its performance is weak, it might not be receiving power on one or even two phases. Shut off the machine immediately and have an electrician check the connection to the supply circuit.
C
Christina HicksAug 22, 2025
What to do if HOLZMANN MASCHINEN BS 712TOP Saw vibrates?
- D
  Danny WagnerAug 23, 2025
  If your HOLZMANN MASCHINEN Saw is vibrating, it could be due to a couple of reasons. It might be placed on an uneven surface, so modify the placement to ensure it's level. Also, motor or other parts might be loose, so check all screw joints and tighten them if necessary.
P
Patricia Richards DVMAug 28, 2025
What to do if HOLZMANN MASCHINEN BS 712TOP band runs in opposite direction?
- J
  Jeffrey McbrideAug 28, 2025
  If the saw band on your HOLZMANN MASCHINEN Saw is running in the opposite direction, two of the three leading phases are likely switched in either the plug or socket. Immediately shut off the machine and have an electrician correct the connection to the supply circuit.

Summary

Preface and Safety Introduction

Important Safety Instructions

Read and follow security instructions for correct product use and to prevent misunderstandings and damages.

Technical Specifications

11.1 Machine Components Overview

Identifies and lists all parts of the machine with corresponding numbers for easy reference.

Technical Details and Delivery

11.2 Detailed Technical Specifications

Provides detailed specifications like voltage, motor power, dimensions, cutting speeds, and weight.

11.3 Package Delivery Content

Lists all the parts included in the package for the user upon purchase.

Safety Guidelines

12.1 Intended and Prohibited Use

Specifies the machine's intended purpose and details operations and conditions that are forbidden.

12.3 Security Instructions

Instructions for avoiding malfunctions, defects, and injuries, including sticker replacement.

Safety Guidelines

General Safety Practices

Provides essential safety practices for operating the machine safely and avoiding accidents.

12.4 Remaining Risk Factors

Identifies inherent risks associated with the machine's design and operation even when used correctly.

Assembly and Setup

13.1 Preparatory Activities

Covers initial checks and requirements before assembling the machine.

13.1.2 Workplace Requirements

Details the necessary conditions for the workplace, including ground stability and electrical supply.

13.1.3 Transport Instructions

Provides instructions and warnings regarding the safe lifting and transportation of the machine.

Assembly and Setup

13.3 Assembly Steps

Detailed instructions for assembling key components like the work stop, hydraulic cylinder, wheels, and V-belt.

Assembly and Setup

13.4 Power Supply Connection

Details electrical connection requirements, safety measures, and checks for proper power supply.

Operation Procedures

14.1 Pre-Operation Checks

Provides essential checks to perform before each workshift and before each cut.

Operation Procedures

14.2 Control Panel Functions

Identifies and explains the function of the main control panel buttons and switches.

14.3 Adjusting Machine Settings

Guides on adjusting the blade tension and blade guides for optimal performance.

14.4 Clamping Workpieces

Instructions on how to properly clamp the workpiece using the vice and end stop.

Operation Procedures

14.5 Setting Cutting Angle

Procedure for setting the desired cutting angle by adjusting the jaw and tightening the nut.

14.6 Adjusting Cutting Speed

Steps to adjust the cutting speed by modifying the V-belt and pulley settings.

14.7 Performing Cuts

Detailed steps on how to perform the actual cutting operation, including starting and stopping.

Maintenance and Care

15.1 Maintenance Plan

Outlines the maintenance schedule, including tasks after each workshift, 50, and 100 hours of operation.

Maintenance and Care

15.2 Changing Saw Blade

Step-by-step guide for safely removing and installing a new saw blade.

Gearbox and Cleaning Procedures

Information on gearbox oil changes and cleaning the machine after each workshift.

15.5 Product Disposal

Guidance on proper disposal of the machine at the end of its lifecycle.

Troubleshooting Common Issues

Power and Motor Problems

Diagnosing and resolving issues with machine power, motor performance, and overheating.

Operational Adjustments and Cuts

Addressing saw band direction, vibration, and problems causing bad cuts.

Electrical Diagrams

Wiring Diagram Explanation

Provides the electrical schematic showing connections between components and their labels.

Spare Parts Information

18.1 Spare Parts Ordering

Instructions on how to order spare parts, emphasizing original parts and service forms.

Spare Parts Information

18.2 Exploded Parts Drawings

Visual representation of the machine's components with numerical identification for parts ordering.

Spare Parts Information

Parts List A

Detailed list of parts for the machine, categorized as 'PARTS LIST A'.

Spare Parts Information

Parts Drawing B

Second part drawing illustrating various components of the machine with reference numbers.

Spare Parts Information

Parts List B

Detailed list of parts for the machine, categorized as 'PARTS LIST B'.

Spare Parts Information

Parts Drawing C

Third part drawing illustrating specific assemblies and components of the machine.

Compliance and Certification

CE Declaration of Conformity

Confirms that the machine meets essential safety and health requirements of EC directives.

Applicable Standards

Lists the European and international standards applied to the machine's design and safety.

Warranty and Service Information

Warranty Terms and Conditions

Details the conditions and terms under which the manufacturer provides warranty for the machine.

Warranty Exclusions

Lists specific conditions and types of defects that are not covered by the warranty.

Warranty and Service Information

Guarantee Claims Process

Explains how to lodge guarantee claims and what information is required.

Guarantee Exclusions

Lists items and conditions not covered by the guarantee, such as wear parts or improper use.

Product Feedback

Customer Experience Input

Section for users to provide feedback, problems, or suggestions about the product.

Service Request Form

Service Form Data Entry

Sections for personal information, machine details, spare parts, and problem description.