HOLZMANN MASCHINEN K5 315VF-2000 User Manual (English)

Questions and Answers:

B
Blake LeonAug 7, 2025
What to do if my HOLZMANN MASCHINEN Cutter does not start?
- J
  jonathanthomasAug 7, 2025
  If your HOLZMANN MASCHINEN Cutter doesn't start, there could be several reasons. First, ensure the emergency stop switch is not activated; turn it to the right to unlock it. Other potential causes include a broken switch or phase, which would require repairing the defective circuit or faulty phase. Check if the overload protection has been triggered and wait for the engine to cool down. Also, inspect the safety fuse and replace it if blown. Finally, make sure the cover plate for the saw blades is closed.
J
Julia RodriguezAug 12, 2025
Why is my HOLZMANN MASCHINEN Cutter workpiece clamped while advancing?
- G
  Gloria LuceroAug 12, 2025
  If the workpiece is clamping while advancing in your HOLZMANN MASCHINEN Cutter, it might be due to a dull blade; replace it with a sharp one. Also, ensure that the riving knife thickness matches the blade being used. The splitting wedge thickness must be greater than or equal to the blade thickness.
T
Tiffany MoralesAug 18, 2025
How to prevent burn marks on the workpiece with HOLZMANN MASCHINEN K5 315VF-2000?
- W
  William GarciaAug 18, 2025
  If you notice burn marks on the workpiece when using your HOLZMANN MASCHINEN Cutter, it's likely that the blade is blunt. Replace the blade to resolve this issue.
J
John JacksonAug 22, 2025
What to do if the cutting width is incorrect on my HOLZMANN MASCHINEN K5 315VF-2000 Cutter?
- J
  Jonathan TaylorAug 22, 2025
  If the finished size of the machined workpiece is incorrect for the cutting width on rip fence for your HOLZMANN MASCHINEN Cutter, the measurement scale for the cutting width display may be adjusted incorrectly. To set the dimension scale: cut the workpiece on the rip fence, measure the workpiece, and move the measuring scale so that the measured average width is shown at the edge of the ruler.
S
steven17Aug 27, 2025
Why are there broken edges on the workpiece with my HOLZMANN MASCHINEN K5 315VF-2000?
- J
  Jason HinesAug 28, 2025
  If you're experiencing broken edges on the workpiece with your HOLZMANN MASCHINEN Cutter, the scoring saw might not be aligned with the main saw. You should set the scoring saw to a new position.
P
Phillip McintyreSep 2, 2025
Why isn't the arm running smoothly on my HOLZMANN MASCHINEN K5 315VF-2000?
- C
  Charles ChavezSep 2, 2025
  If the arm isn't running smoothly on your HOLZMANN MASCHINEN Cutter, the telescopic tube or track rollers might be dirty. Clean the telescopic tube or track rollers. Also, check the wipers.

HOLZMANN MASCHINEN K5 315VF-2000 Specifications

General

Model	K5 315VF-2000
Category	Cutter
Sliding Table	2000 mm
Cutting Width with Rip Fence	1250 mm
Max. Sawblade Diameter	315 mm
Sawblade Bore	30 mm
Sawblade Speed	4000 RPM
Max. Cutting Height 90°	100 mm
Max. Cutting Height 45°	80 mm
Scoring Sawblade Diameter	120 mm
Scoring Sawblade Bore	20 mm
Scoring Sawblade Speed	8000 RPM
Extraction Port Diameter	120 mm
Extraction Port Diameter Saw Guard	80 mm
Voltage	400 V
Frequency	50 Hz