FEATURES
(A) Front hand guard/ (K) Throttle Lock Button
Chain Brake (L) Chain Oil Cap
(B) Front handle (M) Silencer
(C) Cylinder cover (N) Carburettor
(D) Primer bulb Adjustment
(E) Choke Lever (O) Rear handle
(F) Chain (P) Throttle Trigger
(G) Starter Grip (Q) Fuel Mix Cap
(H) Guide Bar (R) On/Off Switch
(I) Chain Catcher (S) Starter/Fan Housing
(J) Trigger Release
OPERATION
For your safety, study this entire manual before operating
the saw. Pay particular attention to the precautions and
instructions listed in the operator’s manual.
WARNING
The warnings and instructions in this section of
the operator’s manual are for your safety and to
prevent serious personal injury.
UNDERSTANDING YOUR CHAINSAW SAFETY
DEVICES
LOW KICK-BACK SAW CHAIN
A low-kick-back saw chain is a chain which has met the
kickback performance requirements.
The rakers (depth gauges) ahead of each cutter can
minimise the force of a kick-back reaction by preventing the
cutters from digging in too deeply at the kick-back zone.
Only use replacement chain that is equivalent to the original
chain or has been certified as a low kick-back chain.
As saw chains are sharpened, they lose some of the low
kickback qualities and extra caution is required.
GUIDE BARS
Generally, guide bars with small radius tips have
somewhat lower kick-back potentials.
CHAIN BRAKE (Fig. 3)
Chain brakes are designed to quickly stop the chain from
rotating. When the chain brake lever/hand guard is pushed
towards the bar, the chain should stop immediately.
A chain brake does not prevent kick-back. The chain brake
should be cleaned and tested daily. Refer to “Operation”
later in this manual for additional information.
Read the operation manual and follow all
warnings and safety instructions.
Wear eye protection and ear protection.
Keep all bystanders, especially children and pets,
at least 15m from the operating area.
SPECIFICATIONS
33 cc 40 cc 45 cc
Weight - No bar, chain, fuel or oil 4.4 kg 4.4 kg 4.4 kg
Fuel tank capacity 575 cm
3
575 cm
3
575 cm
3
Oil tank capacity 350 cm
3
350 cm
3
350 cm
3
Bar lengths 33-50 cm 33-50 cm 33-50 cm
Chain pitch 9.5 mm 8.26 mm 8.26 mm
Chain gauge 1.27 mm 1.27 mm 1.27 mm
Chain type Semi-Chisel, LoPro Semi-Chisel, LoPro Semi-Chisel, LoPro
Drive sprocket 6-tooth 7-tooth 7-tooth
Engine displacement 33 cm
3
40 cm
3
45 cm
3
Engine power (ISO 7293) 1.3 kW 1.5 kW 1.6 kW
Maximum engine power (ISO 7293) 1.5 kW 1.9 kW 2.7 kW
Maximum engine speed with attachment 12,500 min
-1
12,500 min
-1
12,500 min
-1
Idling engine speed 2,800 - 3,400 min
-1
2,800 - 3,400 min
-1
2,800 - 3,400 min
-1
Sound pressure level (ISO 7182) 102 dBA 103.9 dBA 103.9 dBA
Sound power level (ISO 9207) 112 dBA 110 dBA 111 dBA
Vibration (ISO 7505):
- Front Handle 4 m/s
2
3.5 m/s
2
3.5 m/s
2
- Rear Handle 5 m/s
2
7.7 m/s
2
7.7 m/s
2
To Next Page
Loading...
