Homeworks 3070-250-CH-B-WS - User Manual

8 pages

Save Page as PDF

To Next Page

Indoor/Outdoor

Utility Shower Kit

03-20-2020

PACKAGE AND HARDWARE CONTENTS

MODEL

3070-250-CH-B-WS - Chrome

Showerhead ow rate in this unit meets Government standards of

A112.18.1M – 1.8 GPM (6.8 LPM) max at 80 PSI

Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • www.HomewerksWW.com

PREPARATION

SAFETY INFORMATION

Before beginning assembly of product, make sure all parts are present.

Compare parts with package and hardware contents list. If any part is

missing or damaged, do not attempt to assemble the product. Contact

customer service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable Wrench, Slip

Joint Pliers, Pipe Wrench, Phillips Screwdriver, Thread Seal Tape or Pipe

Thread Compound, and Supply Lines.

Installation may vary depending on how the previous shower was

installed. Supplies necessary for the installation of the shower are not

all included; however, they are available wherever plumbing supplies

are sold.

Prior to beginning installation, turn off the hot and cold water lines, then

turn on the old shower to release built-up pressure. When installing the

new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.

Connections that are too tight will reduce the integrity of the system.

Please read and understand this entire manual before attempting to

assemble, operate or install the product.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water

supply lines.

CAUTION

• If you solder the joints during installation of the shower, the seats,

cartridges, and washers must be removed before using a ame

or the warranty will be voided on these parts.

• Cover the sink drain to avoid losing parts.

PART DESCRIPTION QUANTITY

A Showerhead 1

B Shower arm 1

C Soap dish 1

D Mounting screws 2

E Faucet body 1

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757,

7:30 a.m. - 4:30 p.m., CST, Monday - Friday.

Main Page

Questions and Answers

K
Kenneth WebbJul 28, 2025
Why does my Homeworks Bathroom Fixture faucet leak underneath the handle?
- W
  Warren GardnerJul 28, 2025
  A leak under the handle of your Homeworks Bathroom Fixture faucet may be due to a loose bonnet or a dirty or twisted o-ring on the cartridge. To resolve this: 1. Turn the handle to the OFF position, unscrew the handle screw, and remove the handle. 2. Tighten the bonnet clockwise. Move the cartridge stem to the ON position to see if the leak stops. 3. If it doesn't, shut off the water, remove the bonnet, and lift out the cartridge valve. Inspect the o-rings for debris or twisting. Straighten twisted o-rings. If damaged, you should consider replacing the cartridge by calling customer service. 4. Reposition the cartridge in the faucet body, ensuring the ridges fit into the grooves. Tightly screw the bonnet onto the faucet body. 5. Reinstall the handle.
B
Bryan ScottNov 11, 2025
What to do if my Homeworks Bathroom Fixture water does not completely shut off?
- J
  Jamie MartinNov 11, 2025
  If the water in your Homeworks Bathroom Fixture doesn't completely shut off, it might be due to a dirty, stuck, or broken rubber valve seat. Here's what you can do: 1. Shut off the water supply. 2. Remove the handle and loosen the bonnet by turning it counterclockwise. Lift out the cartridge assembly. 3. Inspect the rubber valve seat for debris or brass scrap; remove any found. If the seat is stuck, gently push it with a fingertip to ensure smooth movement. The spring (smaller end up) must be placed back underneath the valve seat. If the rubber valve seat is worn out or broken, replace the cartridge by calling customer service. 4. Reposition the cartridge back into the faucet body, ensuring the ridges fit into the grooves. Tightly screw the bonnet onto the faucet body. 5. Reinstall the han...