Need help?Do you have a question about the Honda Marine BF75A and is the answer not in the manual?
General| Brand | Honda |
|---|---|
| Model | Marine BF75A |
| Category | Outboard Motor |
| Language | English |
Information for operator safety and precautions.
Messages to prevent damage to the motor or property.
Labels warning of potential hazards and injury.
General safety precautions for operation.
Precautions for handling flammable gasoline.
Identifies components of the tiller handle type.
Identifies components of remote control types.
Identifies common components like fuel tank and gauges.
Describes controls for tiller handle type operation.
Describes controls for side-mount remote operation.
Describes controls for panel-mount remote operation.
Describes controls for top-mount remote operation.
Describes common controls like tilt switches and trim tabs.
Procedure for removing and installing the engine cover.
How to check engine oil level and condition.
Checking fuel level and safe refilling procedures.
Recommended unleaded gasoline types and octane rating.
Information on using gasoline blended with oxygenates.
Checking propeller for damage and cotter pin integrity.
Adjusting steering tightness for tiller and remote controls.
Adjusting engine cover lock levers for proper fit.
Various checks including fuel hose, stern bracket, tool kit.
Proper securing and ventilation of the optional fuel tank.
Inspecting and connecting fuel hoses and connectors.
Squeezing the primer bulb to supply fuel to carburetors.
Using ignition switch and setting shift lever to neutral.
Engaging emergency stop switch and verifying cooling system.
Aligning start symbol and warming up the engine.
Verifying the green oil pressure light is ON.
Engaging emergency stop switch and setting control lever to neutral.
Using choke/fast idle lever and ignition switch for starting.
Returning lever, checking cooling system, and oil light.
Warming up the engine based on temperature.
Engaging emergency stop switch and setting control lever to neutral.
Using throttle, choke, and ignition switch for starting.
Adjusting lever, checking cooling system, and oil light.
Engaging emergency stop switch and setting control lever to neutral.
Using throttle, choke, and ignition switch for starting.
Adjusting lever, checking cooling system, and oil light.
Removing covers to access emergency starter.
Setting neutral and activating ignition for starting.
Using manual choke and emergency starter rope.
Adjusting controls and reinstalling covers after starting.
Troubleshooting when starter motor doesn't turn or fails.
Troubleshooting causes for engine not starting after cranking.
Troubleshooting engine stalling and overheating problems.
Recommended break-in procedure for new outboard motors.
How to shift gears using the tiller handle.
How to steer the boat with the tiller handle.
Adjusting trim and throttle for cruising.
How to shift gears with the side-mount control lever.
Adjusting trim and throttle for cruising.
How to shift gears with the panel-mount control lever.
Adjusting trim and throttle for cruising.
How to shift gears with the top-mount control lever.
Adjusting trim and throttle for cruising.
How the power trim/tilt system operates.
Using trim/tilt switches for angle adjustment.
Using the trim meter for performance adjustment.
Manual tilt and trim tab adjustment procedures.
Locking the motor in the tilted position.
Monitoring cooling system and water intake function.
Oil pressure, overheat warnings, and over-rev limiter.
Actions to take when warning systems activate.
Function of anodes for corrosion protection.
Tips for operating the motor in shallow water.
Adjustments for operating at high altitudes.
Procedures for emergency and normal engine shutdown.
Procedures for emergency and normal engine shutdown.
Procedures for emergency and normal engine shutdown.
Procedures for emergency and normal engine shutdown.
Recommendations for trailering and vehicle transport.
Procedures for hoisting and horizontal transport.
Procedures for flushing the motor with water.
Why maintenance is essential and key safety measures.
Information on emission control systems and regulations.
Detailed table of maintenance intervals and tasks.
Engine oil level check, refill, and replacement procedures.
Gear oil specifications and level check.
Spark plug check, gap adjustment, and replacement.
Battery installation, connection, and protection.
Locations and intervals for applying marine grease.
Engine and fuel tank filter check and replacement.
How to replace blown fuses.
Procedure for replacing a damaged propeller.
Immediate service required for a submerged motor.
Procedure for draining carburetors before storage.
Preparing the fuel tank and motor for storage.
Troubleshooting fuel and electrical issues for non-starting engines.
Troubleshooting engine stalling and overheating problems.
Technical specifications for the BF75A model.
Technical specifications for the BF90A model.
Details on starter, ignition, lubrication, and fuel systems.
Information on warranty service and customer relations contact.
Electrical wiring diagram for tiller handle type.
Wiring diagrams for remote control types.
To Next Page