To replace it, position Nozzle onto the front
end while making sure to align the tabs at
the bottom of the Nozzle with the notches on
the foot.
3
The Brush assembly should be free to pull out.
3
Rinse the brushes under running water.
4
Replace them by aligning the center drive
post and note the arrows indicating the front
of the machine. Push firmly until the latches
lock into place.
5
1
Remove the tanks and place the handle in
the upright position, tilt the cleaner back until
handle rests on the floor.
BRUSH CARE
4
Snap Nozzle to foot and rotate the latch into
the lock position.
IMPORTANT: The nozzle must be in the proper
position for the Dirty Water Tank to go on
properly and for the unit to have proper
suction.
Push the latches out on the side of the foot
until they lock open.
2
WARNING:
To reduce the risk of
personal injury, unplug before
cleaning or servicing.
CAUTION:
Use extra care when
cleaning on stairs. To avoid personal
injury or damage, and to prevent the
cleaner from falling, always place
cleaner at the bottom of stairs or on
floor. Do not place cleaner on stairs or
furniture, as it may result in injury or
damage.
2
Align the groove on the backside of the clean
water tank with the handle and drop straight
down.
FILL THE CLEAN WATER TANK
1
Pull up to remove the Clean Water Tank.
2
Remove the cap from the Clean Water Tank.
Add warm water to fill line and replace cap.
OPERATION
CAUTION:
DO NOT USE THIS
EXTRACTOR ON HARD FLOORS. USING
THIS PRODUCT ON HARD FLOORS MAY
SCRATCH OR DAMAGE YOUR FLOOR.
1
Insert the handle into the base.
TROUBLESHOOTING
WARNING:
To reduce the risk
of personal injury, unplug before
cleaning or servicing.
THIS PRODUCT CONTAINS NO SERVICEABLE PARTS.
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR
DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-944-9200 PRIOR TO CONTINUING USE.
CAUTION:
To reduce the risk of
injury from moving parts - Unplug
before servicing. Do not use cleaner
without brushes in place.
ASSEMBLY
GETTING STARTED
Fully assemble product prior to use.
First turn o and unplug the carpet cleaner.
Remove Recovery Tank.
Pull up on the Nozzle slightly to unsnap, then
pull the Nozzle forward to remove it from
carpet cleaner. Rinse with water and allow
to air dry.
2
1
NOZZLE CARE
CAUTION:
To reduce the risk of
injury from moving parts - Unplug
before connecting SpinScrub® Hand
Tool. Not to be used for grooming pets.
This product contains no serviceable parts.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, call customer service at 1.800.944.9200
prior to continuing use.
WARNING:
To reduce the risk of
personal injury, unplug before
cleaning or servicing.
IMPORTANT:
To prevent
possible leaking, remove Clean Water
Tank and Dirty Water Tank.
CORD STORAGE: Wrap the power cord around
the cord hooks for convenient storage. Attach
the plug end to the cord.
MAINTENANCE
LUBRICATION: The motor is equipped with
bearings which contain sufficient lubrication
for their lifetime. The addition of lubricant
could cause damage. Do not add lubricant to
motor bearings.
Using your thumb, push forward and up on
the latch to remove tool.
NOTE: The Antimicrobial pet tool included
with select models only has a button to
release the tool from the hose.
3
1
Place the handle in the upright position. This
will shut o the SpinScrub® brushes
HOW TO USE TOOLS
Connect tool to hose by sliding it onto the
connector until it locks into place.
2
Turn cleaner ON.
4
Pre-spray the carpeted stair by holding the
tool about one inch above the carpet and
push it forward while pressing the trigger
5
Position tool against the riser and slightly
press it into carpet pile. Press the trigger and
pull the tool slowly over the carpet. Release
trigger at end of stroke.
6
Lift tool, and position it against riser. Pull tool
slowly over carpet without pressing trigger.
NOTE: Overlap strokes by 1/2 inch to help
prevent streaking.
7
1
FILL THE SOLUTION TANK
Remove the Solution Tank by pulling it up
and out.
2
Fill the solution tank and replace cap.
CLEANING FLUID
SEE THE HOOVER’S SOLUTION GUIDE insert or
visit Hoover.com/cleaning-solutions.
QUICK CLEAN MODE
HOW TO USE
Return to Deep Clean mode by turning knob
clockwise.
2
Turn unit ON/OFF with side pedal.
2
To engage Quick Clean Mode, turn knob
counterclockwise until engaged.
1
Plug the cord into an electrical outlet.
1
Slide and push the Solution Tank back into
place.
NOTE: Test for colorfastness in a small,
hidden area. Gently rub surface with a
dampened white cloth. Wait ten minutes and
check for color removal or bleed with a white
paper towel.
NOTE: For the best results, vacuum carpet
and upholstery thoroughly with a HOOVER®
vacuum before use.
3
Recline unit with the middle pedal.
3
Squeeze trigger to apply water and cleaning
solution.
4
NOTE: Feature included with select models
only.
CAUTION:
Always turn off
appliance before connecting or
disconnecting hose.
CAUTION:
Not to be used for
grooming a pet.
Attach hose by opening the Hose Connection
Port on the nozzle.
1
Hold open the Hose Solution Port door. Plug
the Hose Solution Tube connector firmly into
the Hose Solution Port.
2
To drain the hose, run the unit and do not
press the spray button on the hose/tool end.
3
The Hose port Door is spring loaded to close
automatically. Ensure the Hose Port Door is
fully shut for the best performance.
NOTE: To ensure maximum performance and
to protect your carpet, be sure to place the
handle in the upright position while using
the hose.
2
Press the button and firmly pull up to remove
the Hose Solution Tube from the Solution Port.
1
USING THE HOSE
REMOVING THE HOSE
Slowly push forward with trigger pressed to
wash, then slowly pull backwards with trigger
released to dry.
NOTE: For Best Results, rinse the carpet after
deep cleaning with clean water only. This will
remove residual carpet cleaning solution from
your carpets. To rinse with clean water only,
remove the solution tank from the unit and
then repeat steps 4 and 5.
5
Turn the cleaner o and unplug from
electrical outlet.
1
HOW TO USE (CONT’D)
EMPTY THE RECOVERY TANK
NOTE: To maintain proper suction, empty Tank
when Red Bobber is visible.
Unlatch the tank lid and empty it. Rinse and
allow to air dry.
3
Grab the Recovery Water Tank handle and lift
up and outward to remove it. A second han-
dle is provided on the back of the Recovery
tank for carrying the tank.
2
On/O
Recline
To Next Page
Loading...