Hoover Reactiv User Manual

DustingBrush**– For bookshelves, frames, keyboards and other delicate areas. [X1]
CreviceTool*– For corners and hard to reach areas. [X2]
FurnitureNozzle*– For soft furniture and fabrics. [X3]
Flexible Crevice Tool * - Ideal for car cleaning. Its length enables cleaning of difcult
areas to reach, narrow crevices. [AB]
LargeDusting BrushwithintegratedFurniture nozzle*- Suitable to clean the soft &
delicate surfaces for both car and home. [AC]
Accessories’bag*- For tidy storage of all the accessories. [AD]
ParquetNozzle*– For parquet oors and other delicate oors. [AA]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hair
removal. [Y]
AllergenRemoverMiniTurboNozzle*–Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal. [Z]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
3
*Certain Models Only ** May vary according to models
3. Remove the pre-motor lter located in the bin lid. [14]
4. Gently tap and wash the pre-motor lter. Do not use hot water or detergents. Remove
excess water from the lter and leave to dry fully before re-using. [17,18]
5. Reassemble the pre-motor lter to the dust bin lid once fully dry and ret to the cleaner.
IMPORTANT: Do not use the product without the lter pack tted.
Toaccesstheexhaustlter:
1. Unlock the exhaust lter door by pressing two buttons and pulling outward from main
cleaner. [15]
2. Remove the lter pack from recess by pulling the ring-pull of exhaust lter. [16]
3. Gently tap and wash the lter unit. Do not use hot water or detergents. Remove excess
water from the lter and leave to dry fully before using. [17,18]
4. Reassemble the Filter pack once it is fully dry and ret to the cleaner by inserting it
back into the location and pushing it fully home. [16]
5. Lock the exhaust lter cover by pressing the edge which has the clips, you will hear a
click once the exhaust lter door ts into place. [15]
IMPORTANT: Do not use the product without the lter pack tted.
Cleaningthedustbin/separationunit
This cleaner uses a separation system unique to Hoover. If necessary the separation unit
can be disassembled from the dust bin and cleaned.
1. Press the dust bin lid release button and remove the dust bin assembly from the
cleaner. [10]
2. Hold the dust bin with one hand and with the other hand press the dust bin lid release
button to open the dust bin lid. [11]
3. Remove the Vortex Finder (Red) from the cyclone body. [12]
4. Remove the cyclone body from the dust bin. [13]
5. If necessary, use a cloth to remove excessive dust from the red vortex nder and the
cyclone body surface.
6. Place the dust bin under the tap. [17] Rinse with lukewarm water. Wash internal
surfaces of the dust bin with water only. DO NOT use soap detergents to wash the
internals of the dust bin.
7. Reassemble the internal component to the dust bin, ensuring all components are dry.
8. Close over the dust bin lid and ret dust bin assembly to cleaner.
Removingablockage
1. Check if the dust bin is full. If so refer to ‘Emptying the dust bin.
2. If the dust bin is empty but suction is still low:
A. Do the lters need cleaning? If so refer to ‘Cleaning the washable lters’.
B. Check if there is any other blockage in the system - Use a rod or pole to remove any
blockage from the extension tube or exible hose.
C. Check if pre-motor lter is tted.
D. Check if the separation unit needs to be cleaned. Refer to ‘Cleaning the separation unit.
CLEANER MAINTENANCE
EmptyingtheDustBin
When the dust reaches the max level indicator in the bin, empty the dust bin.
IMPORTANT: To maintain optimum performance do not allow the dust above the max level
indicator.
1. Turn off the cleaner with the main switch and unplug the power cable.
2. Press the dust bin lid release button and remove the dust bin assembly from the
cleaner. [10]
3. Hold the dust bin with one hand and press the dust bin ap release trigger. [13]
4. Close the dust bin ap and ret to the cleaner main body. [10]
Cleaningthewashablelters
The cleaner is tted with pre-motor lter and exhaust lter. To maintain optimum cleaning
performance, regularly remove the lters and tap against the side of the waste container
to release dust. The lters should be washed every 5 dust container empties or when the
lter has excessive dust level.
IMPORTANT: All bagless cleaners require regular lter cleaning. Failure to clean your
lters may result in air blockage, overheating and product failure. This may invalidate your
guarantee.
IMPORTANT: Regularly check and maintain the lters.
IMPORTANT: Always ensure the lter pack is fully dry before use.
Toaccessthelter:
1.
Press the dust bin lid release button and remove the dust bin assembly from the
cleaner. [10]
2. Hold the dust bin with one hand and with the other hand press the dust bin lid release
button to open the bin lid. [11]
GB

Hoover Reactiv Specifications

General

Brand	Hoover
Model	Reactiv
Category	Vacuum Cleaner
Language	English