EN
Quick Guide
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
WASH CYCLE TABLE
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
1. ON/OFF button
2. DRY ONLY button and indicator light
3. KEY LOCK button and indicator light
4. CLEANING ACTION button
5. CLEANING ACTION indicator lights
6. START/PAUSE button and indicator light
7. DELAY button and indicator light
8. DRYING button
9. SPIN button
10. TEMPERATURE button
11. WASH CYCLE SELECTOR KNOB
DETERGENT DISPENSER DRAWER
Compartment *:
Do not insert detergent in this compartment.
Compartment 1: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, place the partition
into slot B.
Compartment 2: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “MAX” level.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
For all testing institutes:
2) Long cotton cycle: set programme 5 at temperature 40°C.
3) Long synthetics cycle: set cycle 6 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the washer-dryer will drain only.
** If a drying cycle is also programmed, the machine will run a “wash+dry” programme lasting
45’ and a 1kg laundry load.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test programme in compliance with standard EN 50229 (Wash):
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
Test programme in compliance with standard EN 50229 (Drying): select the 10 wash
programme and set the drying level to “A3”, for both loads. The rst drying cycle must be
carried out with the nominal load.
Maximum load 8 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Wash cycle
Temperature
Maximum
spin
(r.p.m.)
Max.
load
(kg)
Duration
(Minutes)
Drying
Wash
Fabric
softener
Powder Liquid
Default Range
1 2
1 Daily Wash & Dry 40 °C
- 40 °C 800 3,0
The duration of the wash cycles can be checked on the display.
–
2 Shirts Wash & Dry 40 °C
- 40 °C 1000 2,0
–
3 Pre Iron – – – 1,5 – – – – –
4 Steam Refresh – – – 2,0 – – – – –
5 Cotton (2) 40 °C
- 60 °C 1400 8,0
6 Synthetics (3) 40 °C
- 60 °C 1000 4,5
7 Anti-Stain Quick 40 °C
- 40 °C 1200 4,5
–
8 Anti-Stain 40 °C
- 40 °C 1400 5,0
–
9 White 60 °C
- 90 °C 1400 8,0
10
Eco Cotton
(1)
60 °C
- 60 °C 1400 8,0
11 Coloureds 40 °C
- 40 °C 1400 8,0
–
12 Ultradelicates 30 °C
- 30 °C 0 1,0
–
13 Wool 40 °C
- 40 °C 800 2,0
–
14 Fast ** 30 °C
- 30 °C 800 3,5
–
Rinse – – 1400 8,0
–
– –
Spin + Pump out * – – 1400 8,0
– – – –
Required dosage Optional dosage
1
11
2
DISPLAY
5
6
7
8
9
10
4
3
To Next Page
Need help?
General
