HP 4284A - Page 30

8-13. COMParator Subsystem Command Tree . . . . 8-65
8-14. Mass MEMory Subsystem Command Tree . . . . 8-76
8-15. STATus Subsystem Command Tree . . . . . . . 8-78
9-1. Serial Number Plate . . . . . . . . . . . . . 9-1
9-2. Test Signal Voltage and Test Frequency upper Limits
to apply measurement accuracy to 2 m and 4 m
Cable Length Operation. . . . . . . . . . . 9-7
9-3. Test Signal Voltage and DC Bias Voltage Upp er
Limits Apply for Measurement Accuracy.. . . 9-8
9-4. Basic Accuracy A (1 of 2) . . . . . . . . . . . 9-12
9-5. Basic Accuracy A (2 of 2) . . . . . . . . . . . 9-13
9-6. Temperature Factor K
e
. . . . . . . . . . . . 9-15
9-7. Maximum Capacitance Voltage . . . . . . . . . 9-22
9-8. Measurement Time . . . . . . . . . . . . . . 9-26
9-9. Rack Mount Kits Installation . . . . . . . . . 9-27
10-1. Test Frequency Accuracy Test Setup . . . . . . 10-5
10-2. Test Signal Level Accuracy Test Setup Using an
Interface Box . . . . . . . . . . . . . . . 10-6
10-3. Test Signal Level Accuracy Test Setup Without an
Interface Box . . . . . . . . . . . . . . . 10-6
10-4. DC Bias Level Accuracy Test Setup Using an
Interface Box . . . . . . . . . . . . . . . 10-9
10-5. DC Bias Level Accuracy Test Setup Without an
Interface Box . . . . . . . . . . . . . . . 10-9
10-6. Imp edance Measurement Accuracy Test Setup . . 10-12
10-7. Correction Page Setup . . . . . . . . . . . . 10-13
10-8. HP-IB Interface Test Setup . . . . . . . . . . 10-21
10-9. Bias Interface Simulator . . . . . . . . . . . . 10-23
10-10. Bias CurrentInterface Function Test Setup . . . 10-24
10-11. Bias CurrentInterface Function Test . . . . . . 10-25
10-12. Interface Board Lo cations . . . . . . . . . . . 10-26
10-13. Jump er Settings . . . . . . . . . . . . . . . 10-27
10-14. Jump er Settings . . . . . . . . . . . . . . . 10-28
10-15. Handler Interface Function Test Set UP . . . . . 10-28
10-16. Handler Interface Function Check . . . . . . . 10-29
10-17. Jump er Settings . . . . . . . . . . . . . . . 10-31
10-18. Handler Interface Function Test Set up . . . . . 10-31
10-19. Handler Interface Function Check . . . . . . . 10-32
10-20. SW1 and SW2 settings . . . . . . . . . . . . 10-34
10-21. Scanner Simulator Connections . . . . . . . . . 10-34
10-22. A7 Board Lo cation . . . . . . . . . . . . . . 10-36
E-1. A7 Digital Board Lo cation . . . . . . . . . . . E-2
E-2. Write Protection Switch. . . . . . . . . . . . E-3
G-1. Required Delay Time After Changing the
Measurement Range (1) . . . . . . . . . . G-3
G-2. Required Delay Time After Changing the
Measurement Range (2) . . . . . . . . . . G-4
G-3. Required Delay Times After Changing the
Measurement Range (3) . . . . . . . . . . G-5
G-4. Required Delay Times After Changing the DC Bias
(1) . . . . . . . . . . . . . . . . . . . G-6
Contents-19