Q1342-90910 xi
Figures
Figure 1. Model and serial number label . . . . . . . . . . . . . . . . . . .3
Figure 2. Front and side view . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Figure 3. Back and side view . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 4. Remove the toner cartridge. . . . . . . . . . . . . . . . . . . . .15
Figure 5. Remove the media tray. . . . . . . . . . . . . . . . . . . . . . . .16
Figure 6. Remove the cable pod . . . . . . . . . . . . . . . . . . . . . . . .17
Figure 7. Remove the left side cover . . . . . . . . . . . . . . . . . . . . .18
Figure 8. Open the straight-through output door . . . . . . . . . . . .19
Figure 9. Remove the back cover. . . . . . . . . . . . . . . . . . . . . . . .20
Figure 10. Remove the ECU PCB fuse . . . . . . . . . . . . . . . . . . . .21
Figure 11. Remove the output sensor . . . . . . . . . . . . . . . . . . . . .22
Figure 12. Remove the motor (fuser removed for clarity). . . . . . .23
Figure 13. Remove the right side cover mounting screw . . . . . . .24
Figure 14. Release the right side cover tab . . . . . . . . . . . . . . . . .25
Figure 15. Remove the right side cover . . . . . . . . . . . . . . . . . . . .26
Figure 16. Disconnect the solenoid wire harness. . . . . . . . . . . . .27
Figure 17. Remove the solenoid. . . . . . . . . . . . . . . . . . . . . . . . . .28
Figure 18. Remove the top cover . . . . . . . . . . . . . . . . . . . . . . . . .29
Figure 19. Remove the connector assembly . . . . . . . . . . . . . . . .30
Figure 20. Remove the LED status panel. . . . . . . . . . . . . . . . . . .31
Figure 21. Remove the front cover mounting screws. . . . . . . . . .32
Figure 22. Remove the front cover. . . . . . . . . . . . . . . . . . . . . . . .33
Figure 23. Release the toner cartridge door connecting links . . .34
Figure 24. Remove the toner cartridge door. . . . . . . . . . . . . . . . .35
Figure 25. Remove the front guide assembly. . . . . . . . . . . . . . . .36
Figure 26. Release the front guide assembly tabs (right side) . . .37
Figure 27. Release the front guide assembly tabs (left side) . . . .38
Figure 28. Remove the transfer roller. . . . . . . . . . . . . . . . . . . . . .39
Figure 29. Disconnect the laser/scanner harnessing . . . . . . . . . .40
Figure 30. Remove the laser/scanner . . . . . . . . . . . . . . . . . . . . .41
Figure 31. Remove the right fuser bracket . . . . . . . . . . . . . . . . . .42
Figure 32. Remove the left fuser bracket . . . . . . . . . . . . . . . . . . .43
Figure 33. Remove the fuser mounting screws . . . . . . . . . . . . . .44
Figure 34. Remove the fuser assembly . . . . . . . . . . . . . . . . . . . .45
Figure 35. Remove the output rollers . . . . . . . . . . . . . . . . . . . . . .46
Figure 36. Remove the face-up rollers . . . . . . . . . . . . . . . . . . . . .47
Figure 37. Remove the gear-clutch assembly . . . . . . . . . . . . . . .48
To Next Page
Loading...