EasyManua.ls Logo

HP TouchSmart 420-1000 User Manual

HP TouchSmart 420-1000
14 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
661940-161 1
English
1 Match the part you received to the illustration on the next page.
2 Go to the page number indicated ( #) for that part.
3 Complete only the part replacement steps in that section.
Español
1 Compare la pieza que usted recibió con l’ilustración en la página
siguiente.
2 Vaya al número de la página indicada ( #) para esa pieza.
3 Ejecute solamente los pasos para el reemplazo de la pieza en esa
sección.
Português
1 Compare a peça que você recebeu com a ilustração na próxima
página.
2 Vá para o número da página indicada ( #) para esta peça.
3 Conclua apenas as etapas de substituição de peças nesta sessão.
Français
1 Repérez la pièce que vous avez reçue sur l’illustration de la page
suivante.
2 Accédez à la page ( #) de cette pièce.
3 Procédez uniquement à la procédure de remplacement détaillée
dans cette section.
IMPORTANT: Follow these part replacement instructions:
WARNING:
Keep your hands away from the moving fan.
Keep fingers and tools clear of the fan when power is applied.
Never open the cover with the power cord attached or power
applied. You may damage your computer or be injured from
the spinning fan blades.
Avoid touching sharp edges inside the computer.
CAUTION: This product contains components that are easily damaged by
electrostatic discharge (ESD). To reduce the chance of ESD damage, work over a
non-carpeted floor, use a static dissipative work surface (like a conductive foam
pad), and wear an ESD wrist strap that is connected to a grounded surface, like the
metal frame of the computer.
IMPORTANT: A hard disk drive is extremely sensitive to shock and impact. Do not
bang or drop it. Do not touch the circuit board. Static electricity can damage the
drive.
NOTE: Computer features may vary by model.
IMPORTANTE: Siga estas instrucciones para el reemplazo de piezas:
ADVERTENCIA:
Mantenga sus manos alejadas del ventilador en
funcionamiento.
Mantenga los dedos y las herramientas lejos del ventilador
cuando lo encienda.
Nunca abra la cubierta cuando el cable de alimentación es
conectado o el ventilador esté encendido. Puede dañarlo o
lastimarse con las aspas en movimiento del ventilador.
Evite tocar los bordes filosos ubicados en el interior del
equipo.
PRECAUCIÓN: Este producto contiene componentes que se pueden dañar con
facilidad si se someten a descargas electrostáticas (ESD). Para reducir las
posibilidades de daños por ESD, trabaje sobre un piso no alfombrado, utilice una
superficie de trabajo estática disipativa (como una goma espuma conductora) y
use una muñequera contra ESD que esté conectada a una superficie con conexn
a tierra, como el marco de metal de su equipo.
IMPORTANTE: La unidad de disco duro es extremadamente sensible a los golpes.
No la golpee ni la deje caer. No toque la tarjeta de circuito. La electricidad estática
puede dañar la unidad.
NOTA: Las características del equipo pueden variar según el modelo.
IMPORTANTE: Siga estas instruções sobre substituição de peças:
AVISO:
Mantenha suas mãos longe do ventilador.
Mantenha os dedos e ferramentas longe do ventilador
quando o mesmo estiver ligado.
Nunca abra a tampa com o fio de alimentação conectado ou
quando estiver ligado. Você pode danificar seu computador
ou se machucar com as lâminas do ventilados.
Evite tocar em bordas pontiagudas dentro do computador.
AVISO: Este produto contém componentes que podem ser facilmente danificados
por descarga eletrostática (ESD - Electrostatic Discharge). Para reduzir o risco de
danos por ESD, não trabalhe sobre carpetes, use uma área de trabalho
antiestática (semelhante a um revestimento de espuma condutora), e utilize uma
pulseira própria para evitar descargas eletrostáticas que esteja conectada a uma
superfície aterrada, como a estrutura metálica do computador.
IMPORTANTE: A unidade de disco rígido é extremamente sensível a choques e
impacto. Não bata ou derrube a unidade. Não toque na placa de circuito.
Eletricidade estática pode danificar a unidade.
OBSERVAÇÃO: Os recursos do computador podem variar de acordo com o
modelo.
IMPORTANT : Suivez ces instructions relatives au remplacement des
pièces :
AVERTISSEMENT :
Gardez vos mains à l’écart du ventilateur en mouvement.
N’approchez pas vos doigts ou des outils du ventilateur
lorsque l’ordinateur est alimenté.
N’ouvrez jamais le capot lorsque le cordon d’alimentation est
branché ou lorsque l’ordinateur est sous tension. Vous
pourriez endommager votre ordinateur.
Évitez de toucher les bords tranchants à l’intérieur du châssis.
ATTENTION : Ce produit contient des composants qui peuvent être endommagés
facilement par des décharges électrostatiques. Pour diminuer les risques de
dommages par décharges électrostatiques, travaillez au-dessus d’un plancher non
revêtu de moquette, utilisez une surface de travail antistatique (un tapis conducteur
en mousse par exemple), et portez un bracelet antistatique relié à une surface mise
à la terre, comme le cadre métallique de l’ordinateur.
IMPORTANT : Un disque dur est extrêmement sensible aux chocs. Ne le laissez
pas tomber et ne le heurtez pas. Ne touchez pas la carte de circuit intégré.
L’électricité statique peut endommager le disque.
REMARQUE : Les caractéristiques de l’ordinateur peuvent varier selon le modèle.
Question and Answer IconNeed help?

Do you have a question about the HP TouchSmart 420-1000 and is the answer not in the manual?

HP TouchSmart 420-1000 Specifications

General IconGeneral
Storage1 TB HDD
Display Resolution1920 x 1080
Operating SystemWindows 7 Home Premium
Wireless802.11 b/g/n
RAM6 GB
Display23-inch Touchscreen
Optical DriveSuperMulti DVD burner
WebcamIntegrated webcam with microphone
Networking10/100/1000 Gigabit Ethernet
PortsUSB 2.0, HDMI, Ethernet

Summary

General Part Replacement Guidelines

Part Replacement Instructions

Follow these steps for part replacement.

Safety Warnings

Important safety precautions to avoid injury or damage.

ESD Precautions

Measures to prevent damage from electrostatic discharge.

Hard Drive Replacement

Initial Preparation and Access

Prepare the system and access the hard drive bay (Steps 1-6).

Removing the Hard Drive Assembly

Detailed steps for removing the hard drive assembly (Steps 7-12).

Installing the New Hard Drive

Instructions for installing the replacement hard drive (Steps 13-18).

Finalizing Hard Drive Replacement

Completing the hard drive replacement process (Steps 19-24).

CD/DVD Drive Replacement

Initial Preparation and Access

Prepare the system and access the CD/DVD drive bay (Steps 1-6).

Removing the CD/DVD Drive

Detailed steps for removing the CD/DVD drive (Steps 7-12).

Installing the New CD/DVD Drive

Instructions for installing the replacement CD/DVD drive (Steps 13-20).

Finalizing CD/DVD Drive Replacement

Completing the CD/DVD drive replacement process (Steps 21-22).

Memory Modules Replacement

Initial Preparation and Access

Prepare the system and access the memory module slots (Steps 1-6).

Removing Memory Modules

Detailed steps for removing existing memory modules (Steps 7-12).

Installing New Memory Modules

Instructions for installing new memory modules (Steps 13-18).

Finalizing Memory Module Replacement

Completing the memory module replacement process (Steps 19-23).

Related product manuals