HP xw4200 - Setting Up RAID with Manual OS Installation; RAID Setup Steps with Manual OS Install

2nd Hard Disk Drive –
One of the following
Windows XP Red Hat Linux
2nd hard drive, 40 GB 7200 rpm Serial ATA drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 80 GB 7200 rpm Serial ATA drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 160 GB 7200 rpm Serial ATA drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 250 GB 7200 rpm Serial ATA drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 400 GB 7200 rpm Serial ATA drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 74 GB 10K rpm Serial ATA drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 73 GB 10K Ultra320 SCSI drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 300 GB 10K Ultra320 SCSI drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 36 GB 15K Ultra320 SCSI drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 73 GB 15K Ultra320 SCSI drive 32-Bit, 64-Bit 7.2, 7,3, WS3
2nd hard drive, 146 GB 15K Ultra320 SCSI drive 32-Bit, 64-Bit 7.2, 7,3, WS3
Factory Integrated
RAID
Windows XP Red Hat Linux
RAID 0 Configuration – Striped Array 32-Bit
RAID 1 Configuration – Mirrored Array 32-Bit
NOTE: Requires 2 identical hard drives (speeds, capacity, interface)
Drive controllers Windows XP Red Hat Linux
Integrated 4 channel Serial ATA controller with RAID 0, 1
functionality
32-Bit
Optional SCSI controllers (required with SCSI HDDs) 32-Bit 7.2, 7,3, WS3
Memory –
One of the following*
Windows XP Red Hat Linux
256 MB DDR-2 PC2-4200 (533 MHz) ECC (1 x 256 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
512 MB DDR-2 PC2-4200 (533 MHz) ECC (2 x 256 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
1 GB DDR-2 PC2-4200 (533 MHz) ECC (2 x 512 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
1.5 GB DDR-2 PC2-4200 (533 MHz) ECC (2 x 256 MB, 2 x 512 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
2 GB DDR-2 PC2-4200 (533 MHz) ECC (2 x 1 GB) 32-Bit, 64-Bit 7.2, 7,3, WS3
2 GB DDR-2 PC2-4200 (533 MHz) ECC (4 x 512 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
3 GB DDR-2 PC2-4200 (533 MHz) ECC (2 x 512 MB, 2 x 1 GB) 32-Bit, 64-Bit 7.2, 7,3, WS3
4 GB DDR-2 PC2-4200 (533 MHz) ECC (4 x 1GB) 32-Bit, 64-Bit 7.2, 7,3, WS3
128 MB DDR-2 PC2-3200 (400 MHz) non-ECC (1 x 128 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
256 MB DDR-2 PC2-3200 (400 MHz) non-ECC (2 x 128 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
512 MB DDR-2 PC2-3200 (400 MHz) non-ECC (2 x 256 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
1 GB DDR-2 PC2-3200 (400 MHz) non-ECC (4 x 256 MB) 32-Bit, 64-Bit 7.2, 7,3, WS3
NOTE: Do not mix ECC and non-ECC memory. The system will not boot if ECC and non-ECC DIMMs are mixed. Only unbuffered DDR2
DIMMs are supported. All DIMMs must be either x8 or x16 width.
QuickSpecs
HP xw4200 Workstation
Standard Features - Custom Components
DA - 12022 Canada — Version 25 — August 15, 2005 Page 4