HQ Power PS1310 - User Manual

To Next Page

PS1310 VELLEMAN 1

PS1310 - DC-REGULATED POWER SUPPLY 13.8V/10A

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm

the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialised

company for recycling.

This device should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for buying the PS1310! Please read the manual thoroughly before bringing this device into service. If the

device was damaged in transit, don't install or use it and contact your dealer.

2. Operation

1. Insert the AC power plug in a 220V-outlet.

2. Connect the power cord of a device with the appropriate input voltage to the output binding posts on the front

panel. The red positive (+) terminal and black negative (-) terminal are indicated on the front panel. Mind the

polarity: reversal of polarity may damage the device.

3. Put the ON/OFF switch on the front panel in the "ON"-position. The light in the switch will come on.

4. The 220V-input is protected by the fuse, which is located at the back of the device. Replace a blown fuse with an

identical one.

5. This device is protected against brief short circuits and equipped with an automatic reset function.

3. Warning

 Do not use the PS1310 with devices requiring an input current > 10A.

 Do not use this device outdoors and do not expose it to rain, water or other liquids.

 Do not open the housing yourself. Have the device repaired by qualified personnel.

 Let the device cool for 10 minutes for every half hour of use at full power.

 Select a location where the working of the heat sink will not be impeded by walls or large objects.

Also consult the wiring diagram.

The information in this manual is subject to change without prior notice.

PS1310 - DC-GESTUURDE VOEDING 13.8V/10A

1. Inleiding

Aan alle ingezetenen van de Europese Unie

Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn levenscyclus wordt weggeworpen,

dit toestel schade kan toebrengen aan het milieu.

Gooi dit toestel (en eventuele batterijen) niet bij het gewone huishoudelijke afval; het moet bij een

gespecialiseerd bedrijf terechtkomen voor recyclage.

U moet dit toestel naar uw verdeler of naar een lokaal recyclagepunt brengen.

Respecteer de plaatselijke milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke autoriteiten inzake verwijdering.

Referencia Electrónica Embajadores: SA6A110

Need help?

Do you have a question about the HQ Power PS1310 and is the answer not in the manual?

The PS1310 is a DC-regulated power supply, designed to provide a stable 13.8V/10A output. This device is suitable for various electronic applications requiring a consistent and regulated power source. It is identified by the electronic reference SA6A110.

Function Description:

The primary function of the PS1310 is to convert AC power from a standard 220V outlet into a regulated DC output of 13.8V with a maximum current of 10A. This makes it ideal for powering devices that require a stable DC voltage and current within these specifications. The unit features output binding posts on the front panel, clearly marked with red for positive (+) and black for negative (-) terminals, ensuring correct polarity connection. An ON/OFF switch with an indicator light is located on the front panel for easy operation. The device is also equipped with protection mechanisms, including a fuse for the 220V input and protection against brief short circuits, featuring an automatic reset function.

Important Technical Specifications:

Output Voltage: 13.8V DC
Maximum Output Current: 10A
Input Voltage: 220V AC
Protection:
- 220V input fuse (located at the back of the device)
- Short-circuit protection with automatic reset
Terminals: Red positive (+) and black negative (-) binding posts on the front panel.

Usage Features:

Connection: To operate the PS1310, first insert the AC power plug into a 220V outlet. Then, connect the power cord of the device to be powered to the output binding posts on the front panel, ensuring correct polarity (red for positive, black for negative). Reversing polarity can damage the connected device.
Operation: Once connected, switch the ON/OFF button on the front panel to the "ON" position. The indicator light within the switch will illuminate, signifying that the power supply is active.
Fuse Replacement: In case of a blown fuse, which protects the 220V input, it can be found at the back of the device. Always replace a blown fuse with an identical one to ensure continued protection and proper functioning.
Short-Circuit Protection: The PS1310 is designed with protection against brief short circuits and includes an automatic reset function, which helps prevent damage to the unit and connected devices during unexpected current surges.
Environmental Considerations: The device should not be used outdoors or exposed to rain, water, or other liquids. It is recommended to select a location where the heat sink's operation will not be impeded by walls or large objects to ensure proper cooling.

Maintenance Features:

Cooling: For optimal performance and longevity, allow the device to cool for 10 minutes after every half hour of use at full power. This prevents overheating and ensures stable operation.
Repair: The housing of the PS1310 should not be opened by the user. Any repairs or servicing must be carried out by qualified personnel to avoid damage to the unit and ensure safety.
Fuse Maintenance: Regularly check the fuse if the device fails to power on. Replace it with an identical fuse if it is blown.
Environmental Disposal: In line with European Union environmental guidelines, the PS1310 should not be disposed of as unsorted municipal waste at the end of its lifecycle. It should be returned to the distributor or a local recycling service for proper recycling. This symbol on the device or packaging indicates that improper disposal can harm the environment. Users are encouraged to respect local environmental rules and contact local waste disposal authorities if in doubt about disposal procedures.
Pre-use Inspection: Upon receiving the PS1310, it is important to inspect it for any damage that may have occurred during transit. If any damage is found, do not install or use the device and contact your dealer immediately.

The information provided in the manual is subject to change without prior notice, reflecting potential updates or improvements to the device. The wiring diagram is also available for consultation for detailed technical understanding.