HQ RC UNI/AIRCO3 User Manual

RC UNI/AIRC03
ENGLISH
INSTRUCTIONS
1. Panel description
1 Run mode display
2 Signal sending display
3 Blowing direction display
4 Model code
5 Temperature “-“ key
6 Mode key
7 Automatic blowing direction control key
8 Power key
9 Fast cool
key
10 Timing off key
11 Enter key
12 Clock function key
13 SET
14 Timing
on key
15 Fast heat key
16 Fan key
17 Blowing direction control key
18 Temperature “+” key
19 Fan display
20 Temperature display
9
10
11
12
13
14
15
17
18
19
20
16
1
2
3
4
5
6
7
8
1
2. Installing the batteries
Remove the battery cover of the remote control and install two AA size batteries.
Install the battery cover. The time will appear in the left corner of the LCD display.
3. Set up instructions
Method A: digital automatic search set up.
Method B: direct code setup.
a) Refer to the CODE FORM and find the number corresponding with your brand.
Power on the air conditioner by hand. For example: INYCIN is code 188-190.
b) Hold the "SET" button( for about 3 seconds) until the code flashes in the display.
Press temperature "+" or "-" until the code you want to choose is shown.
c) Press “ENTER” and the code stops flashing.
d) Check whether the keys on the remote control work normally. If not, repeat
steps b-d until a suitable code is found.
4. Timing on/off function
Press “Timing on” key to increase the starting time for the air conditioner by 1 hour.
The displayed time is the time when the air conditioner will automatically be
switched on. Pressing “Timing off” key will delay the time the air conditioner will be
turned off by 1 hour each time the key is pressed. The timing function uses a 15 h
indication to show and set up the time.
5. Fast cool/Fast heat function
Press the “Fast cool” key to automatically set the air conditioner to 21 degrees C,
middle wind, automatic blowing direction. Or, press the “Fast heat” key to
automatically set the air conditioner to 27 degrees C, middle wind and automatic
blowing direction.
6. Notes
Make sure the air conditioner is in working order. Be aware that the remote control
cannot increase the function of the air conditioner. If the remote control will not be
used for a long time, make sure to remove the batteries to prevent damage to the
remote control.
Safety precautions:
To reduce risk of electric shock, this product should ONLY be opened by an
authorized technician if service is required. Disconnect the product from mains and
other equipment if a problem should occur.
Warranty:
No guarantee or liability can be accepted for any changes and modifications of the
product or damage caused due to incorrect use of this product.
General:
Designs and specifications are subject to change without notice.
2
a) Turn on air conditioner and aim the remote control directly at it
b) Hold the "SET" button until the code changes in the mode
window.Then release it.The system will switch to automatic
search and the code will increase with 1 unit every two
seconds.Pay attention to the air conditioner.Keep searching
until the air conditioner automatically turns on/off. Press the
'ENTRY'key to finish set up.

HQ RC UNI/AIRCO3 Specifications

General

Maximum range	8 m
Number of devices supported	-
Interface	IR Wireless
Input type	Press buttons
Product color	White
Buttons quantity	14
Housing material	ABS synthetics
Remote control proper use	Air conditioner
Built-in display	Yes
Battery type	AAA
Number of batteries supported	2
Package type	Blister
Package weight	160 g

Weight and Dimensions

Depth	150 mm
Width	50 mm
Height	23 mm
Weight	70 g

Summary

RC UNI/AIRC03 Remote Control Panel Description

Run Mode Display

Displays the current operating mode of the air conditioner, such as cool, heat, or fan.

Signal Sending Display

Indicates when the remote control is sending a signal to the air conditioner unit.

Blowing Direction Display

Shows the current setting for the air conditioner's airflow direction.

Model Code

Displays the specific model code of the air conditioner being controlled.

Temperature Decrease Key

Decreases the set temperature by one degree Fahrenheit or Celsius.

Mode Selection Key

Allows cycling through different operating modes like Cool, Heat, Fan, Auto.

Automatic Blowing Direction Control

Controls the automatic swing function for the air conditioner's louvers.

Power Key

Turns the air conditioner unit on or off.

Fast Cool Key

Activates rapid cooling mode for quick temperature reduction.

Timing Off Key

Sets a timer for the air conditioner to automatically turn off.

Enter Key

Confirms selections or operations within the remote control interface.

Clock Function Key

Accesses or sets the real-time clock function of the remote.

SET Key

Used in setup procedures to initiate or confirm settings.

Timing On Key

Sets a timer for the air conditioner to automatically turn on.

Fast Heat Key

Activates rapid heating mode for quick temperature increase.

Fan Speed Key

Controls the fan speed settings for the air conditioner.

Blowing Direction Control Key

Manually adjusts the direction of airflow from the air conditioner.

Temperature Increase Key

Increases the set temperature by one degree Fahrenheit or Celsius.

Fan Display

Shows the current fan speed setting or mode.

Temperature Display

Displays the current room temperature or the set temperature.

Installing the Batteries

Remote Control Setup Instructions

Method A: Digital Automatic Search Setup

Automatically searches for the correct code by aiming the remote at the AC.

Method B: Direct Code Setup

Manually enters a specific code from a provided list for brand compatibility.

Timing On/Off Function

Fast Cool and Fast Heat Function

Important Notes and Safety Precautions

Applicable Brand and Code List