Huber MPC Minichiller 600 User Manual

MPC Minichiller®

Huber MPC Minichiller 600 Specifications

General

Temperature Range	-20°C to +40°C
Cooling Capacity at 20°C	0.6 kW
Pump Capacity	15 L/min
Pump Pressure	0.5 bar
Power Supply	230 V / 50 Hz
Pump Flow Rate	15 L/min
Cooling Capacity	0.6 kW (at 20°C)
Refrigerant	R134a

Summary

1.3 Safety (Continued)

1.3.3 Proper Operation

Details correct operational procedures and safety warnings.

1.3 Safety and Responsibilities

1.4 Responsibilities and Disposal

1.4.1.2 Temperature Control Unit with Natural Refrigerants (NR)

Details safety precautions for units using natural refrigerants.

1.4 Refrigerant Handling and Classification

1.4 Refrigerant Regulations and Safety

1.5 Protective Devices and Power Interruption

2.4 Installation Conditions and Safety

Electrical Installation Safety

Warns about electrical safety during installation and connection of power supply.

2.8 Preparations for Operation

2.9 Connecting External Applications and Power Supply

2.9.1 Connecting an Externally Closed Application

Explains how to connect external applications to the unit.

2.10.1 Connection using Socket with Protective Earth (PE)

Covers connecting the unit to a grounded power socket.

2.10 Power Supply and Wiring Safety

2.10.2 Connection via Hard Wiring

Provides instructions for connecting the unit via hard wiring, emphasizing electrician involvement.

3 Function Description

3.2 Information on Thermal Fluids

Provides essential information and safety warnings regarding thermal fluids.

3.3 Notes for Test Planning

Test Planning Considerations

Offers advice for planning tests and system setup.

3.4 Display and Control Instruments

4 Setup Mode

4.1.3 Setting the Overtemperature (OT) Protection

Details how to set and understand the overtemperature protection.

4.1 Setup Mode (Continued)

4.1.3.2 Setting the Overtemperature Protection

Guides on adjusting the overtemperature cut-off value using a screwdriver.

4.1.4 Testing Overtemperature Protection Functionality

Explains how to test the overtemperature protection for proper operation.

4.1 Setup Mode and Fluid Handling

4.2 Filling, Venting and Draining

Outlines steps for filling and venting the system with thermal fluid.

4.2.1 Filling and Venting with Sight Glass

Filling and Venting Steps (Sight Glass)

Provides detailed instructions for filling and venting using the sight glass.

4.2.1 Filling and Venting with Level Indicator and Drain

Filling and Venting Steps (Level Indicator/Drain)

Details filling and venting process using the level indicator and drain.

4.2.2 Draining Externally Closed Applications

Draining via Sight Glass

Step-by-step guide for draining using the sight glass.

4.2.2 Draining with Level Indicator and Drain

Draining via Level Indicator/Drain

Details the process of draining using the level indicator and drain.

5 Normal Operation: Automatic Control

5.1.1 Starting the Temperature Control Process

Explains how to initiate the temperature control process.

5.1.1.2 Ending the Temperature Control Process

Details the procedure for stopping the temperature control process.

7 Service/Maintenance: Fault Displays

7.1 Displays in the Event of Faults

Lists error messages, causes, and corrective actions for the unit.

7.2 Maintenance: Visual Inspections

7.2.1 Function Check and Visual Inspection

Details routine functional checks and visual inspections and their intervals.

7.2 Maintenance: Hose Replacement and Cleaning

7.2.2 Replacing Temperature Control or Coolant Hoses

Step-by-step guide for replacing temperature control and coolant hoses.

7.3 Thermal Fluid Inspection, Replacement and Circuit Cleaning

Thermal Fluid Inspection and Replacement

Covers inspection, replacement, and cleaning of thermal fluid circuits.

7.3 Thermal Fluid Management

7.3.1 Thermal Fluid Replacement

Guidelines for replacing thermal fluids and avoiding mixing different types.

7.3.2 Rinsing the Thermal Fluid Circuit

Instructions on how to rinse the thermal fluid circuit when changing fluids.

7.3 Circuit Rinsing Procedures

7.3.2.1 Rinsing a Thermofluid Circuit with Sight Glass

Steps for rinsing the circuit using the sight glass.

7.3.2.2 Rinsing the Thermofluid Circuit with Level Indicator and Drain

Steps for rinsing the circuit using the level indicator and drain.

7.6 Plug Contacts and 7.7 Decontamination/Repairs

7.7 Decontamination/Repairs

Procedures for decontamination before repair or unit return.

8 Shutting Down the Unit

8.1 Safety Instructions and Basic Principles

Key safety instructions to follow before shutting down the unit.

8.3 Draining and 8.4 Cooling Water Draining

8.4 Draining the Cooling Water System

Step-by-step guide for draining the cooling water system.

8.9 Disposal and 8.10 Contact Information

8.9 Disposal Guidelines and Regulations