IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED. READ ALL INSTRUCTIONS.
TO PROTECT AGAINST RISK OF ELECTRICAL SHOCK, DO NOT PUT THE
MAIN BODY (MOTOR) IN WATER OR ANY OTHER LIQUID.
CLOSE SUPERVISION IS NECESSARY WHEN ANY APPLIANCE IS USED
NEAR CHILDREN.
UNPLUG FROM OUTLET WHEN NOT IN USE, BEFORE ASSEMBLING OR
TAKING OFF PARTS AND BEFORE CLEANING.
AVOID CONTACT WITH MOVING PARTS.
DO NOT OPERATE ANY APPLIANCE WITH A DAMAGED CORD OR PLUG, OR
AFTER THE APPLIANCE MALFUNCTIONS, OR IS DROPPED OR DAMAGED
IN ANY MANNER. RETURN APPLIANCE TO THE NEAREST AUTHORIZED
SERVICE FACILITY FOR EXAMINATION, REPAIR OR ELECTRICAL OR
MECHANICAL ADJUSTMENT.
THE USE OF ATTACHMENTS NOT RECOMMENDED OR SOLD BY THE
MANUFACTURER MAY CAUSE FIRE, ELECTRIC SHOCK OR INJURY.
1.
2.
3.
4.
5.
6.
7.
02 11
English
01
02
누름
누름
정회전
역회전
정지상태
작동스위치
정회전
역회전
off(정지)
정지
01 Open the hopper cover.
① Pull the hopper cover lever to open it.
Inserting an excessive amount of ingredients may exert
severe pressure on the product.
02 Add ingredients only up to the limit mark of the
hopper.
① For soft ingredients, mixing them with other
ingredients for extraction.
03 Close the hopper cover and keep the juice cap open.
① Before pressing the ON button, put the juice
container in place.
② The juice may flow backwards into the hopper if the
juice cap is closed during extraction. If the juice does
not come out even after opening the juice cap, open the
hopper cover and empty out the contents.
04 Press the power switch briefly to start operation.
① The "click" sound during the operation of the product
is the sound of the chamber set and the motor being
locked together.
05 To add more ingredients during operation, use the
additional inlet or open the hopper cover.
① When the hopper cover is opened, the operation
stops.
② Do not use anything other than the designated
pusher.
③ In case the Multi-screw spins but the ingredients fail
to be ground in the hopper during extraction, use the
pusher to press the ingredients down.
06 Empty out the pulp container and juice container so
that they are not filled up.
07 Let the machine operate for about 1 more minute
after all ingredients go down in the hopper.
① It slowly presses and squeezes the ingredients so it
takes some time until the last ingredient is juiced.
② Removing the remaining pulp by additionally
operating the machine after extraction makes it more
convenient to detach the hopper and clean the parts.
③ It is easy to remove residual pulp when repeatedly
operating reverse and normal rotations.
08 Once the juicing and pulp removal are finished,
press the power switch to stop the machine.
① The machine stops 3 seconds after it is stopped by
the power switch.
09 Pour any remaining juice by tilting the chamber
forward.
① For thickly concentrated juice made of tomatoes, etc.,
the juice may still remain in the chamber.
② When detaching the chamber, pulp may drip from the
product body depending on the ingredients being juiced.
8. When Multi-screw Stops
During Use
01
Press and hold [REV] button for 3 to 5 seconds
and release the button 2 to 3 times.
[REV] button pushes the ingredients back up to
dislodge. Reverse rotation continues only when the
button is pressed while the screw stops when the
button is released.
02
After reverse rotation stops completely,
press the [ON] button to run operation.
When pressing the [ON/Extract] or [REV/Reverse]
button, make sure to press it after the
screw stops moving completely.
Note
If the machine does not work even after following the
above steps, pull the power cord plug from the outlet,
detach the chamber set, wash it and use it again. Due
to its characteristics, the motor will not stop at once
but, instead, continue to spin slowly in the direction of
operation before coming to a complete stop.
10
04
07
05
08
06
09
01
03
02
누름
정회전
역회전
정지상태
작동스위치
정회전
역회전
off(정지)
정지
7. How to Use
To Next Page
Loading...
Need help?
General