10 HUSKY INSTRUCTION MANUAL HUSKY INSTRUCTION MANUAL 11
Press SET again and the lower display will flash. Set the desired temperature by pressing the UP
or DOWN buttons as described above.
INTERIOR LIGHT
To turn the interior light ON or OFF, first unlock the control panel (see page 9) then push the
button marked with the “Light” symbol. The light will turn off automatically after 10 minutes.
DOOR REVERSAL
The doors cannot be reversed on these Husky appliances.
MAINTENANCE & CLEANING
Disconnect the appliance from the power before cleaning. Always reconnect the
plug with dry hands. Never pour water over the appliance.
Interior Cleaning
• Wash the interior with warm water and neutral detergent such as bicarbonate of soda
(5ml to 0.5 litres of water)
• Do not use abrasive products, detergents or soaps
• Wipe the wooden shelves with the same solution.
• Dry all surfaces thoroughly.
Exterior Cleaning
• Wash the outer cabinet including the back and bottom of the appliance with warm
soapy water.
• Do NOT use abrasive products as this can damage the finish
• Once or twice a year dust the fans within the appliance with a brush or vacuum
cleaner to maintain efficient performance
• Dry all surfaces thoroughly.
WHEN YOUR APPLIANCE IS NOT IN USE
If the appliance is not being used for long periods:
• Unplug your appliance
• Clean and dry the inside of the appliance. Leave the door slightly open to allow it to
dry completely
• An appliance which is unused without being cleaned may start to smell musty or
develop mildew.
POWER FAILURE
If a power cut occurs, do not open the door more often than necessary in order to conserve
cold air. Wait at least 15 minutes before restarting. If you attempt to restart the unit before
this delay, the appliance may not start.
TROUBLESHOOTING
Before returning your appliance to where you purchased it from, check the following points as
you may be able to solve any problem yourself.
The appliance does
not work
Internal temperature
too high or low
The temperature is
not cold enough
Problem Solution
• Check that the appliance is turned on
• Check power cable is plugged in and that the fuse has not blown
• Check that the voltage is correct for the appliance
• Try a different socket which is known to work
• Check that the control panel is not locked.
• Check thermostat – is it set too high or low?
• The correct clearances are at the sides/back
• The door is not being opened too often
• The door is not closing completely.
• Check power cable is connected and that the fuse has not blown
• The wrong temperature selected. Adjust temperature (see page 9)
• The appliance is overfilled
• Appliance exposed to direct sunlight or heat source
• The door is being opened too often or the door gasket is damaged
• Check that the ambient temperature is within the operational limits of
the appliance
• Check that the temperature is set to a suitable temperature.
Unusual noises or
noisy operation
Outer surfaces are wet • Water source or leak too near the appliance – dry surfaces thoroughly
and move the appliance
• Inner surfaces are wet
• Caused by condensation – dry the inside of the appliance
• Door opened too often or kept open too often.
• Check that the appliance is on a flat, level surface and is stable
• Check the clearance around the appliance and that it is not touching any
other items
• Shelves are out of position
• Hoover the dust from the fan(s).
Inner surfaces are wet
Inner surfaces are
iced up
• Caused by condensation – dry the inside of the appliance
• Door is opened too often or kept open too long.
• Door opened too often or left open, or the ambient temperature is too
high or too humid.
Continued overleaf...
Not achieving
temperature set
• The temperature shown on the display is showing the temperature of
where the sensor is located. It is perfectly normal operation for the
temperature to read a different temperature to the set temperature, as
the temperature within the appliance will fluctuate continually.
• Temperature performance is affected by several factors, i.e. how often the
door is opened, the ambient temperature, how full the appliance is, etc.
• If the temperature shown is higher than the set temperature, there is no
need to reset as the appliance will be continually working to reach the
required set temperature.
• Check that there is sufficient ventilation around the unit.
To Next Page
Loading...
