Husqvarna 580 RSW - Page 17

17
F RICTION W HEEL AND D RIVE
Model 580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC, 600 C
Item Part No. Qty. Description
12 606 00 01 81 1 Gear-Pinion
13 606 00 01 85 2 Bearing - Ball .562 x 1.375 x .437 (600 C)
14 606 00 01 75 1 Drive Mount
15 606 00 02 12 1 Spring-Tension .051 x .60 x 2.25
16 606 00 01 73 1 Drive Actuator Weldment
17 606 00 01 80 1 Pivot Channel Weldment
18 606 00 00 50 2 Nut-Locking-Center .31-18
19 606 00 00 45 2 Washer-Flat-Steel .344 x .688 x .065
20 606 00 01 27 2 Bolt-Round Head Square Short Neck .31-18 x .62
21 606 00 01 63 1 Rod-Guide
22 606 00 01 98 1 Washer - Flat - Steel 1.390 x 2.00 x .020
23 606 00 00 78 2 Push Nut .25
24 606 00 01 93 2 Pin-Roll .125 x .50 (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
606 00 01 94 2 Pin-Roll .125 x .63 ((600 C)
25 606 00 01 61 2 Shift Link
26 606 00 01 60 1 Shift Arm Weldment
27 606 00 01 62 1 Retainer Plate
28 606 00 01 64 1 Hex Shaft
29 606 00 01 92 2 Pin - Roll .188 x .88
30 606 00 01 77 2 Thrust Plate (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
31 606 00 02 11 4 Screw-Tapping 10-24 x .375 Hex Washer Head (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
32 606 00 01 78 1 Guide-Plate (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
33 606 00 02 14 1 Friction Wheel Assembly (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
34 606 00 02 05 1 Nut-Hex .31-18
35 606 00 01 99 1 Washer-Locking .312 x .097 Heavy
36 606 00 02 03 1 Washer Flat-Steel .328 x .875 x .062
37 606 00 01 65 1 Friction Sheave
38 606 00 01 88 2 Bearing-Ball .625 x 1.375 x .43
39 606 00 02 00 1 Washer- Flat-Steel 1.062 x 1.344 x .032
40 606 00 01 66 1 Spindle, Bearing
41 606 00 01 67 1 Bearing, Retainer
42 606 00 01 97 1 Bolt-Round Head Square Neck .31-18 x 1.75 Grade 5 (600 C)
43 606 00 01 89 2 Ring-Retaining-External .579 x .930
44 606 00 01 79 1 Friction Ring (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
45 606 00 01 76 1 Friction Wheel Hub (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
46 606 00 00 92 4 Screw-Tapping 12-24 x .50 Hex Washer Head (580 R, 580 RS, 580 RSE, 580 RSW, 580 BBC)
606 00 00 92 8 Screw-Tapping 12-24 x .50 H
ex Washer Head (600 C)
47 606 00 01 95 3 Bolt-Hex .25-20 x .50 Grade 5 (600 C)
48 606 00 01 82 1 Disc, Friction (600 C)
49 606 00 01 71 1 Hub, Friction Wheel (600 C)
50 606 00 00 49 3 Nut-Locking-Center .25-20 (600 C)
51 606 00 01 70 1 Bearing Plate (600 C)
52 606 00 01 69 1 Bearing Retainer (600 C)
53 606 00 01 86 1 Bearing Ball 1.00 x 2.00 x .56 (600 C)
54 606 00 01 58 1 Bearing Retainer (600 C)
55 606 00 01 91 1 Ring-Retaining - External 1.00 x .042 (600 C)
56 606 00 01 57 2 Fitting-Lube .25-28 x .256 ((600 C)
* Available as individual components or part of 606 00 02 71 Service Kit which consists of (2) 606 00 01 88, (1) 606 00
01 84 , (2) 606 00 01 85 and (2) 606 00 01 22.
Key # 33 was a friction wheel assembly which had a rubber ring on a plastic hub. The plastic hub in NLA from the
supplier. The replacement is a complete assembly with new brackets and a new friction wheel. (Dec 2008)