Husqvarna Blastrac BMR 25P User Manual (English)

Questions and Answers:

G
Gregory GuerreroAug 5, 2025
Why is my Husqvarna Blastrac BMR 25P vibrating so much?
- K
  kelseygrahamAug 6, 2025
  If your Husqvarna Construction Equipment is vibrating too much or making unusual noises, several issues could be the cause. Check if the blast wheel or its blades are worn or damaged and replace them if necessary. Ensure the blast wheel is correctly leveled and that all screws and nuts are tightened. Inspect the tension of the drive belt for the shot blaster head. Also, lubricate the blast wheel bearings. For engine or wheel damage, consult an approved Husqvarna service agent.
O
Oscar AguirreAug 10, 2025
How to stop abrasive material from falling out of my Husqvarna Blastrac BMR 25P Construction Equipment?
- W
  Willie ChapmanAug 11, 2025
  If abrasive material is falling out of your Husqvarna Construction Equipment, check the pinch bar's position and replace it if worn, open the dust valve if it's closed, and replace clogged primary filters, checking for leakages. Adjust the height of the abrasive material seals and the shot blaster head to ensure they are at the correct distance from the surface. Inspect all seals for damage and replace as necessary.
J
Jennifer AdamsAug 15, 2025
Why does my Husqvarna Construction Equipment not move?
- A
  Adam TylerAug 16, 2025
  If your Husqvarna Construction Equipment isn't moving, try increasing the speed. Check if the shot blaster head is getting caught on the floor and adjust its height. Ensure that the emergency stop button is not engaged; turn it clockwise to disengage. For a damaged drive system, it's best to speak to your dealer for more information.
R
Robert VasquezAug 21, 2025
Why is there excessive wear on the shot blaster head of my Husqvarna Blastrac BMR 25P?
- B
  beckergraceAug 21, 2025
  If parts of the shot blaster head on your Husqvarna Construction Equipment are wearing more than usual, replace the abrasive material with the correct type for the surface. Also, replace the primary filters to ensure sufficient suction power in the dust collector.
A
Amy SmithAug 27, 2025
Why won't the engine start on my Husqvarna Blastrac BMR 25P Construction Equipment?
- R
  Rebekah HarrellAug 27, 2025
  If the engine of your Husqvarna Construction Equipment won't start, first check if the propane tank is empty and fill it if necessary. Ensure the propane tank valve is open and the battery switch is in the ON position. If the battery is empty, charge it with a workshop charger. For a damaged engine, it's best to speak to an approved Husqvarna service agent.
E
Ernest SchwartzAug 30, 2025
What to do if my Husqvarna Construction Equipment stops after a while?
- D
  Daisy GreenAug 30, 2025
  If your Husqvarna Construction Equipment stops after running for a while, fill the propane tank if it's empty. However, if the engine is damaged, or a safety fuse or fault current breaker is activated, it's best to speak to an approved Husqvarna service agent.

Husqvarna Blastrac BMR 25P Specifications

General

Brand	Husqvarna
Model	Blastrac BMR 25P
Category	Construction Equipment
Language	English

Summary

Introduction and Product Basics

Owner Responsibility

Outlines the owner's obligations for safe product use and operator knowledge.

Product Description and Intended Use

Details the product's function, intended applications, and materials.

Regulatory Information

Notes CARB classification and California Proposition 65 warning regarding exhaust emissions.

Product Overview

Control Panel and Safety Symbols

Control Panel Layout

Details the layout and function of the product's control panel buttons and indicators.

Product Safety Symbols

Explains the meaning of various safety and warning symbols found on the product.

Safety Definitions and Product Plate

Product Damage Conditions

Lists conditions under which the manufacturer is not responsible for product damage.

Safety Terminology

Defines the terminology used for warnings, cautions, and notes in the manual.

Type Plate Details

Describes the details found on the product's identification or type plate.

General and Operational Safety

General Safety Instructions

Provides fundamental safety rules for using the product safely and preventing injury.

Operational Safety Instructions

Outlines specific precautions to take before and during product operation.

Specific Safety Hazards

Vibration, Dust, and Noise Safety

Details risks associated with vibrations, dust inhalation, and noise exposure.

Personal Protective Equipment

Guidance on selecting and using appropriate personal protective equipment.

Fuel, Exhaust, and Work Area Safety

Propane and Exhaust Fumes Safety

Covers safety precautions for propane handling and risks from exhaust emissions.

Work Area Safety Guidelines

Provides guidelines for ensuring a safe operating environment, including weather and debris.

Safety Devices and Controls

Emergency Stop and Seat Belt Use

Details the function and checking procedure for the emergency stop button and seat belt.

Operator Presence Control (OPC)

Explains the function of the operator presence control system for safety.

Component Safety and Maintenance Safety

Muffler and Hydraulic Safety

Warns about muffler heat and hydraulic system risks.

Maintenance Safety Instructions

Critical safety guidelines to follow before and during maintenance tasks.

Operation Preparation Checks

Pre-Operation Checklist

Lists essential checks and preparations required before starting product operation.

Abrasive Material System Setup

Abrasive Material Valve and Seals

Explains operation of the abrasive material valve and adjustment of seals.

Separator and Filling Procedures

Separator Operation and Filling

Describes separator function and instructions for filling with abrasive material.

Pressure Tank Manometer

Explains the purpose and typical pressure reading of the pressure tank manometer.

Component Operation and Speed Selection

Dust Valve and Propane Tank Connection

Instructions for operating the dust valve and connecting the propane tank.

Selecting Correct Operating Speed

Guidance on choosing the appropriate speed for different surfaces and treatments.

Product Starting and Operation

Starting the Product

Step-by-step guide for starting the product safely and correctly.

Operating the Product

Instructions for operating the shot blaster head, clutch, and movement controls.

Operational Procedures and Dust Disposal

Stopping the Product and Blast Pattern

Procedures for stopping the product and factors affecting the blast pattern.

BigBag Dust Collector Handling

Instructions for safely emptying and replacing the dust collector BigBag.

System Draining and Adjustment

Pressure Tank Water Drain

Explains the daily procedure for draining accumulated water from the pressure tank.

Suction Power and Pinch Bar Adjustment

Details adjusting suction power and turning the pinch bar.

Maintenance Schedule

General Product Maintenance Tasks

Details routine maintenance tasks performed by the operator and their frequency.

Cleaning, Lubrication, and Seals

Product and Dust Collector Cleaning

Guidelines for cleaning the product exterior, air openings, and dust collector.

Lubrication and Seal Replacement

Instructions for lubricating grease nipples and replacing front/side seals.

Component Replacement Procedures

Pinch Bar and Brush List Seal Replacement

Steps for replacing the pinch bar and the brush list seal.

Blast Wheel Maintenance

Blast Wheel Blades and Wheel Replacement

Procedures for replacing blast wheel blades and the main blast wheel assembly.

Drive Belt and Filter Maintenance

Drive Belt Tension and Air Filter Replacement

How to check drive belt tension and replace the air compressor filter.

Primary Filter Replacement

Instructions for replacing the product's primary filters.

Filter and Propane Tank Procedures

HEPA Filter Replacement

Detailed steps for safely replacing the HEPA filter.

Propane Tank Filling

Procedure for safely refilling or replacing the propane tank.

Engine and Fuel System Checks

Propane System Examination

How to inspect propane tanks and lines for leaks.

Engine Oil and Spark Plug Checks

Procedures for checking engine oil level and examining the spark plug.

Spark Plug and Hydraulic System Checks

Spark Plug Replacement

Instructions for replacing the spark plug, including gapping and torque.

Hydraulic System Checks

Procedures for checking hydraulic hoses, oil level, and replacing hydraulic oil.

Hydraulic Oil Filter Replacement

Hydraulic Oil Filter Replacement Steps

Detailed steps for replacing the hydraulic oil filter, including lubrication.

Troubleshooting

Troubleshooting and Error Codes

Reading and Interpreting Error Codes

How to interpret error codes displayed by the product's diagnostic tool.

Error Codes and Transportation

Error Code Descriptions

Lists specific error codes, their causes, and recommended solutions.

Transportation Safety

Safety precautions and instructions for transporting the product.

Moving, Lifting, and Storage

Ramp Operation and Lifting

Safety instructions for moving on ramps and lifting the product.

Securing and Storage

Guidance on attaching the product to a vehicle and proper storage recommendations.

Technical Data

Product Specifications

Provides detailed specifications for product dimensions, engine type, power, and fuel.

Operating Specifications and Emissions

Operating Conditions and Hydraulic Data

Lists operating temperature, humidity, vibration, and hydraulic system parameters.

Abrasive Material and Noise Data

Specifies approved abrasive materials and declared noise emission levels.

Product Dimensions and Accessories

Product Dimensions

Visual representation and measurements of the product's length, width, and height.

Available Accessories

Lists compatible accessories and their corresponding item numbers.

Related product manuals

Husqvarna Blastrac EBE 500

Husqvarna Soff-Cut 2000

104 pages

Husqvarna Soff-Cut 4000

Husqvarna 970 55 16-02

20 pages

Husqvarna Blastrac BMR 25P User Manual

Table of Contents