To Next PageTo Next Page
Need help?Do you have a question about the Husqvarna CT153 and is the answer not in the manual?
Learn controls and proper use. Never allow unqualified persons or children to operate.
Follow safety rules for engine use, slopes, traffic, and leaving operator position.
Inspect for fire hazards, remove debris, wear proper clothing, inspect area before use.
Assemble steering wheel, extension shaft, and related components securely.
Install the steering wheel extension shaft and related components.
Remove hardware, place seat on pan, engage slots, and tighten bolt securely.
Lift lever, slide seat for comfortable position, release lever to lock.
Secure battery door stand, connect cables correctly, charge battery before installation.
Connect the hood vent to the machine's designated port.
Assemble bagger frame, fabric loops, and attach to tractor securely.
Adjust bagger pivot brackets for proper gap between fender and assembly.
Adjust bagger handle/extension for grass type and desired output.
Identify and understand the location and function of all tractor controls.
Operate the tractor's lights.
Regulate engine speed and blade speed using the throttle lever.
Control tractor braking and declutching the engine/blades.
Select forward, neutral, or reverse gears for tractor movement.
Engage or disengage the cutting unit and blades using the lever.
Adjust cutting deck height for terrain and transport using the lever.
Start, stop, and secure the engine using the ignition key.
Engage and disengage the parking brake for securing the tractor.
Fill the engine with unleaded petrol, following safety precautions.
Check engine oil level, add SAE 30 or 5W-30 as needed.
Maintain correct tire pressure for optimal performance and safety.
Follow steps to safely start the engine using the ignition and throttle controls.
Instructions for lowering cutting unit, engaging drive, and selecting appropriate speed.
Understand and safely use the Reverse Operation System for maneuvering.
Tips for optimal mowing results, including blade height and grass conditions.
Instructions for converting mower to mulching, rear discharging, or bagging modes.
Procedure for safely emptying the bagger and deactivating the alarm.
Do not leave ignition key in the machine to prevent unauthorized starting.
Disconnect spark plug wire before any maintenance or repair work.
Perform routine checks on oil, fasteners, battery, air screen, engine, and brakes.
Clean the machine and steering plate, avoid high-pressure washers.
Remove debris from steering plate to ensure proper function of controls.
Procedure for draining and refilling engine oil with safety precautions.
Log all maintenance dates and hours for regular service tracking.
Verify that operator presence and ROS safety systems function correctly.
Handle sharp blades with care, ensure proper sharpening and installation.
Ensure blades are correctly installed and sharpened equally for balance.
Steps for removing mower blades, noting patterns and thread types.
Details for removing and installing a 5-star pattern blade.
Details for removing and installing a 6-star pattern blade.
Check brake effectiveness by stopping distance and manual test.
Procedure for removing and installing the mower drive belt.
Adjust neutral position of gear shift lever if needed.
Troubleshoot issues preventing the engine from starting, checking fuel and ignition.
Troubleshoot issues with the starter motor not turning the engine, checking battery and connections.
Diagnose and fix causes of uneven engine operation, checking gears, plug, and carburetor.
Identify and resolve issues causing the engine to perform weakly, checking air filter and fuel system.
Troubleshoot causes of engine overheating, checking load, cooling, oil, and ignition.
Diagnose and fix issues preventing the battery from charging, checking fuse and connections.
Troubleshoot problems with the lighting system, checking wiring, bulbs, and switches.
Identify causes of machine vibration, such as loose blades, engine, or imbalance.
Troubleshoot issues leading to uneven grass cutting, checking blades, deck, tire pressure.
Follow steps for cleaning, oil change, fuel draining, and battery storage for seasonal storage.
Provide necessary mower details when ordering parts or requesting service.
General| Oil Filter | Yes |
|---|---|
| Transmission Type | Hydrostatic |
| Cutting Width | 97 cm |
| Blades | 2 |
| Deck Material | Steel |
| Tyre Size Front | 15x6.00-6 |
| Blade Engagement | Electric PTO |
