Need help?Do you have a question about the Husqvarna FS 309 and is the answer not in the manual?
The product is a walk behind floor saw with a 4-stroke gasoline engine.
Product is for wet cutting hard floor surfaces with diamond blades; other uses are incorrect.
Labeled diagram identifying all major parts of the floor cutting machine.
Explains warning symbols and their meanings for safe operation.
Details conditions under which the manufacturer is not liable for product damages.
Clarifies the meaning of WARNING, CAUTION, and NOTE symbols used in the manual.
Provides essential safety guidelines and precautions for product operation.
Warns about carbon monoxide in exhaust fumes and the need for good ventilation.
Addresses risks of injury from product vibrations and symptoms to watch for.
Discusses noise safety and the use of approved hearing protection.
Details other required PPE like helmets, gloves, and eye protection.
Covers safety devices, fire extinguishers, and the machine stop button.
Instructions for checking the blade guard for correct installation and damage.
Instructions for checking the drive belt cover for damage and secure fit.
Guidance on checking the muffler for defects and awareness of its high temperature.
Safety warnings and procedures for handling flammable gasoline during refueling.
Steps to take before performing maintenance, including stopping the engine and cleaning.
Pre-operation checklist including reading manuals, daily maintenance, and preparing the work area.
Warning about using blades only for their intended materials.
Requirements for diamond blades, including speed compatibility and standards.
Emphasizes aligning the blade's rotation direction with the product's indicator.
Advice on sharpening blunt blades and handling hot blades after use.
Importance of water for cooling blades and preventing dust, ensuring supply is not clogged.
Warnings about gasoline flammability and correct fueling procedures.
Step-by-step guide to loosening levers, setting height, and tightening.
Instructions for loosening, adjusting, and tightening the track widener for stability.
Detailed steps for installing a cutting blade, including safety checks.
Safety precautions and steps for removing or replacing the cutting blade.
Steps for mounting the blade, flange, and screw, ensuring correct rotation.
Guide on how to set the cutting depth indicator and lower the blade safely.
Steps to adjust the indicator plate to the '0' position for correct depth indication.
Procedure to align the pointer with the cutting blade for accurate guidance.
Guidance on proper technique, avoiding side grinding, and securing materials.
Safety warning to ensure the cutting blade is slightly above ground before starting.
Steps to lift the cutting blade and stop the water supply to halt operation.
Instructions for using the machine stop button in an emergency.
Procedure to turn the engine ON/OFF switch to the OFF position.
Steps to take before maintenance: park on level surface, stop engine, clean area.
Reference to engine manual for engine parts maintenance and daily/weekly checks.
Steps for lowering blade, making guide cuts, and aligning with marks.
Adjusting water supply for blade cooling and dust prevention during operation.
Daily tasks: cleaning surfaces, air filter, general inspection, oil level, drive belt, guards, muffler, blade.
Ensuring sufficient water flow and cleaning blocked supply holes in the blade guard.
Warnings about protective glasses and avoiding water on electrical components.
Steps for cleaning the product, including checking for leaks and cleaning openings.
Checks for tightened nuts and screws, cable condition, fuel/oil leaks, and seals.
Procedure for loosening screws, adjusting tension nuts, and checking pulley alignment.
Instructions for lubricating components, including grease nipples for cutting depth adjustment.
Steps to check the engine oil level using the dipstick and adding oil if needed.
Procedure for draining warm engine oil and safety warnings regarding hot oil.
Safety warnings and procedures for cleaning or replacing the air filter.
Guidance on when to examine the spark plug and tips for preventing electrode issues.
Safety warnings and procedures for transporting the heavy product.
Recommendations for storing the product safely, including removing the blade and fuel.
Instructions for disposing of chemicals and the product according to regulations.
Warnings about using correct lifting equipment and ensuring the lifting eye is not damaged.
Table detailing specifications like engine power, dimensions, weight, and speeds.
Data on sound power and sound pressure levels for the product.
Explanation of declared noise and vibration values obtained from laboratory testing.
Declaration of conformity with EU directives and applied standards for the product.
Declaration of conformity with UK directives and standards for the product.
To Next Page
General