To Next PageTo Next Page
Need help?Do you have a question about the Husqvarna TC 38 and is the answer not in the manual?
General| Engine Manufacturer | Briggs & Stratton |
|---|---|
| Cylinder | 1 |
| Fuel Type | Gasoline |
| Transmission Type | Hydrostatic |
| Cutting Width | 97 cm |
| Cutting Height Min-Max | 38-102 mm |
| Blade Engagement | Manual |
| Collector Volume | 220 liters |
| Fuel Tank Capacity | 5.7 liters |
| Tire Size, Front | 15x6-6 |
| Tire Size, Rear | 18x8.5-8 |
Understand controls and proper equipment use. Never allow untrained persons or children to use.
Prepare for safe operation: inspect area, wear proper footwear, and handle fuel safely.
Operate safely: avoid confined spaces, mow in daylight, disengage blades, use caution on slopes.
Maintain equipment for safety and condition. Store properly to prevent hazards.
Identify and prepare parts that require assembly before operating the tractor.
Securely fasten the seat assembly to the tractor seat pan before use.
Properly connect the battery cables to the tractor for safe operation.
Install the hood vent component onto the tractor's engine cover.
Identify and understand the function of various bagger components.
Assemble the bagger by following step-by-step instructions.
Adjust hanger brackets for proper gap between fender and bagger top.
Adjust the vertical position of the plate for proper alignment.
Adjust the horizontal position of the plate for proper alignment.
Install the bagger spring latch securely to the back plate.
Install the bagger's full lever or extension assembly.
Adjust the bagger's full lever or extension to the desired position.
Safely remove mower blades, protecting hands from sharp edges.
Install the 5-star pattern blade correctly, ensuring proper bolt and alignment.
Install the 6-star pattern blade correctly, ensuring proper bolt and alignment.
Procedure for removing and installing the mower drive belt.
Steps to safely remove the mower drive belt.
Instructions for installing the mower drive belt correctly.
Identify and understand the location and function of key tractor controls.
Regulate engine speed and blade rotation using the throttle/choke lever.
Use the pedal for declutching, braking, and starting the engine.
Operate the gear shift lever for forward, neutral, and reverse.
Engage or disengage the cutting unit using the lever.
Lift or lower the cutting unit quickly for terrain or transport.
Understand the four positions of the ignition key for tractor operation.
Engage and release the parking brake correctly.
Fill fuel tank safely with fresh, unleaded gasoline; do not overfill.
Check engine oil level regularly and maintain it between markings.
Check and maintain correct tire inflation pressure for proper operation.
Safely start the engine by following specific pedal and ignition key procedures.
Understand and use the Reverse Operation System (ROS) safely.
Tips for achieving optimal cutting results and lawn care.
Empty the grass bagger when full, following safety procedures.
Properly shut down the engine and tractor.
Perform pre-operation checks for safety and functionality.
Clean the tractor and mower components using appropriate methods.
Remove debris from the steering plate to ensure smooth operation.
Procedure for safely changing the engine oil.
Handle and maintain the battery safely, including removal and installation.
Steps for safely removing the battery from the tractor.
Perform routine maintenance checks on the battery.
Steps for safely installing the battery onto the tractor.
Ensure mower deck is level for optimal cutting performance.
Visually adjust mower deck side-to-side for even cutting.
Precisely adjust mower deck side-to-side for even cutting.
Adjust mower deck front-to-back for optimal cutting results.
Identify and resolve issues preventing the engine from starting.
Troubleshoot issues when the starter motor does not engage.
Diagnose and fix causes for uneven engine operation.
Address issues causing the engine to perform weakly.
Resolve causes of engine overheating.
Troubleshoot battery charging problems.
Diagnose and fix issues with the tractor's lighting system.
Identify and resolve causes of excessive machine vibration.
Address factors causing uneven grass cutting.
Prepare the tractor for storage at the end of the mowing season.
Provide necessary information when ordering service parts or repairs.
Product description: Combustion-engine-powered ride-on lawn mower.
Manufacturer's brand name.
Product model and type information.
Product batch and serial number information.
Relevant EU directives and regulations applicable to the product.
Description of applicable EU directives and regulations.
