Husqvarna TS 354XD 2022 User Manual (English)

Questions and Answers:

T
Thomas JonesAug 20, 2025
How to fix Husqvarna TS 354XD 2022 Lawn Mower engine that does not start?
- S
  Stephanie CrawfordAug 20, 2025
  If your Husqvarna Lawn Mower engine isn't starting, several factors could be at play. First, ensure there's fuel in the tank and that the throttle control is in the correct position, consulting the start instructions if needed. A defective spark plug, dirty air filter, or clogged fuel filter can also prevent starting, so inspect and replace them as necessary. Water or bad fuel in the tank can be another cause; in this case, remove the old fuel, replace the fuel filter and refill with fresh fuel. Check all wires for looseness or damage. If the engine is flooded, wait 2–3 minutes before attempting to restart. For engine valve issues, it's best to speak with an approved service agent.
C
Cassandra SantiagoAug 21, 2025
What to do if Husqvarna TS 354XD 2022 Lawn Mower starter motor does not turn the engine over?
- S
  Stephen RoseAug 21, 2025
  If the starter motor on your Husqvarna Lawn Mower isn't turning the engine over, the battery may be too weak, so charge it. Ensure the attachment clutch control is disengaged and the clutch/brake pedal is fully pushed down when starting the engine. Check the battery connections for any issues. If the main fuse is defective, replace it. For issues related to the ignition lock, safety connector for the clutch/brake pedal, starter motor, solenoid, or operator presence control (OPC), it is recommended to speak to an approved service agent. If the OPC is defective, also check the wires, switches and connections.
M
Michael ChenAug 25, 2025
Why Husqvarna Lawn Mower engine backfires when the engine stops?
- C
  Chad MoyerAug 25, 2025
  If your Husqvarna Lawn Mower engine backfires when it stops, make sure that the throttle control is put in the slow position.
R
Ralph FigueroaAug 26, 2025
What to do if Husqvarna TS 354XD 2022 engine does not run smoothly?
- N
  nhicksAug 27, 2025
  If your Husqvarna Lawn Mower engine isn't running smoothly, several factors could be the reason. A defective spark plug or a dirty air filter can cause this issue, so replace or clean them accordingly. The fuel tank being nearly empty or water being present in the fuel can also lead to rough running. Make sure to fill the fuel tank or remove the water. Additionally, a defective check valve on the fuel tank cap or a clogged fuel filter could be the culprit; consider replacing these parts. If the choke is engaged while the engine is warm, disengage it. Ensure you're using the correct fuel mix or fuel type. If there's dirt in the carburetor or fuel line, clean them. For an incorrectly adjusted carburetor, it's best to consult an approved service agent.
C
Crystal BaileyAug 29, 2025
What to do if Husqvarna Lawn Mower battery does not charge?
- L
  Larry CardenasAug 30, 2025
  If your Husqvarna Lawn Mower battery isn't charging, start by checking the main fuse and replacing it if defective. If the fuse is fine, the battery itself may be defective and need replacement. Ensure the charging cable is properly connected. Also, inspect the battery connections for any issues and correct them.
H
howardvalerieSep 1, 2025
How to fix Husqvarna TS 354XD 2022 Lawn Mower blades that cannot rotate?
- Z
  zcookSep 1, 2025
  If the blades on your Husqvarna Lawn Mower cannot rotate, start by checking for any blockage in the clutch mechanism and remove it. If there is no blockage, inspect the drive belt for the cutting deck for wear or damage, and replace it if necessary. Also, check the idler pulley and blade mandrel, replacing them if either is frozen.
T
Timothy MorrisSep 3, 2025
What to do if Husqvarna Lawn Mower moves slowly, with irregular speed or not at all?
- Z
  zballardSep 3, 2025
  If your Husqvarna Lawn Mower is moving slowly, with irregular speed, or not at all, first check if the product is in freewheel mode and pull out the freewheel control lever. Ensure the parking brake is disengaged. If the drive belt is loose or damaged, replace it. For air in the transmission, remove it. Clean the product if there are unwanted materials on the steering plate (if installed). If the square key on the axle is missing, install it.
T
Teresa StoneSep 5, 2025
Why my Husqvarna TS 354XD 2022 Lawn Mower engine becomes too hot?
- A
  Anthony GreenSep 5, 2025
  An overheating Husqvarna Lawn Mower engine could be due to several reasons. Overload in the engine can cause it to overheat, so decrease the workload. Check the air intake and cooling fins on the engine for blockages, and clean them if necessary. The engine oil level may be too low, so check it and add oil if needed. Also, a defective spark plug can contribute to overheating, so replace it. For issues related to the cooling fan or ignition lock, it's best to speak to an approved service agent.
J
Jesus HarrisSep 7, 2025
Why Husqvarna Lawn Mower has vibration?
- G
  Gloria WilsonSep 7, 2025
  If your Husqvarna Lawn Mower is vibrating, check if the blades are loose and tighten the bolts. Also, inspect the blades for damage or imbalance, and balance or replace them as necessary. Finally, ensure the engine bolts are tightened, as a loose engine can also cause vibration.
C
Candice BakerSep 9, 2025
Why Husqvarna TS 354XD 2022 Lawn Mower has defective grass discharge?
- L
  Lisa DavenportSep 9, 2025
  Defective grass discharge in your Husqvarna Lawn Mower can occur for several reasons. Ensure the engine speed is set correctly by putting the throttle control in the fast position and avoid operating the product at too high a forward or rearward speed. If the grass is wet, allow it to dry before cutting. Check the cutting deck to ensure it is parallel, and adjust if necessary. Verify that the tire pressure is correct. Inspect the blades for wear, damage, or looseness, and replace or tighten them as needed. Clean any buildup of grass or dirt below the cutting deck and around the mandrels to open air holes. If the drive belt for the cutting deck is worn or damaged, replace it. Make sure the blades are installed with the sharp edge down, and that the correct blades are used.

Husqvarna TS 354XD 2022 Specifications

General

Engine Manufacturer	Kawasaki
Cutting Width	54 inches
Transmission Type	Hydrostatic
Cutting Height Min	1.5 inches
Deck Material	Steel
Seat Material	Vinyl
Cylinders	2
Engine Cooling	Air
Battery	12 V
Oil Filter	Yes
Transmission Manufacturer	Hydro-Gear
Drive Method	Pedal-operated
Blades	3
Blade Tip Speed	18500 fpm
Anti-scalp Wheels	Yes
Deck Wash Port	Yes
Deck Construction	Fabricated
Nose Roller	Yes
Seat Type	High back
Armrests	Yes
Hour Meter	Yes
Service Minder	Yes
Cup Holder	Yes
Front Axle Material	Cast Iron
Tire Size Front	16x6.5-8
Tire Size Rear	23x10.5-12
Turning Radius	16 inches
Warranty	3 years
Cutting Height Max	4 inches
Battery CCA	230 A
Blade Engagement	Electric
Steering Wheel Type	Ergonomic
Engine Type	V-Twin

Summary

Introduction to the Lawn Tractor

Pre-delivery Inspection and Product Numbers

Details about pre-delivery checks and identifying product numbers for the lawn tractor.

Product Description and Accessories

Overview of the lawn tractor, its features, and optional accessories.

Intended Use Guidelines

Defines the proper and intended use of the lawn tractor, including limitations and safety precautions.

Support and Assistance

Information on how to get assistance or help regarding the product operation and maintenance.

Product Overview and Controls

Control Identification

Identifies and describes the main components and controls of the lawn tractor via a diagram.

Product Symbols

Explains the meaning of various warning and operational symbols found on the product itself.

Operator Symbols and Indicators

Function Indicators

Explains the meaning of various operational symbols and their corresponding functions on the tractor.

Hazard Indicators

Details specific hazard symbols and their safety implications for operation and maintenance.

Safety Information

Hazard Symbol Explanations

Details the meaning of hazard symbols like hot surfaces, fire, and cruise control indicators.

Product Liability Statement

Outlines the manufacturer's liability concerning product misuse, repair, and approved parts.

Emissions Compliance

Provides information regarding Euro V emissions and warnings about tampering.

Safety Definitions

Defines the terms WARNING, CAUTION, and NOTE as used within the manual for safety instructions.

Safe Operation Practices

Child Safety Warnings

Addresses the risks to children and provides safety guidelines for their presence around the equipment.

General Operation Safety

Covers essential safety rules for operating the machine, including clearance, bystander safety, and general conduct.

Safe Operation Practices (Continued)

Personal Protective Equipment (PPE)

Recommends specific personal protective equipment (PPE) for safe operation, such as hearing and eye protection.

Safety Device Checks

Explains the importance of safety devices and checks for operator presence control (OPC) and reverse operation system (ROS).

Operation Safety Guidelines

Muffler Safety Precautions

Warns about the hot muffler and potential fire risks with flammable materials.

Safe Slope Operation

Provides detailed instructions and warnings for safely cutting grass on slopes, including angle limits and maneuvers.

Parking Brake Functionality

Emphasizes the importance of a functional parking brake and the risks if it fails.

Fuel and Battery Safety

Fuel Handling Safety

Details critical safety measures for handling flammable fuel to prevent fire and explosion hazards.

Battery Handling Safety

Outlines safety precautions for handling batteries, including risks of explosion and short circuits.

Assembly Procedures

Removing Product from Carton

Step-by-step guide on how to safely unpack the tractor from its shipping carton.

Required Assembly Tools

Lists the necessary tools for assembling the product, including wrenches and utility knives.

Loose Parts Identification

Identifies the specific parts that need to be assembled after unpacking the product.

Seat Installation and Adjustment

Installing the Seat

Provides instructions for securely installing the seat onto the tractor frame.

Adjusting Seat Position

Guides on how to adjust the seat forward/backward for comfortable operation.

Adjusting Seat Height

Explains how to adjust the seat height to one of two positions for optimal operator comfort.

Battery Connection and Pre-Operation Checks

Connecting the Battery

Step-by-step instructions for safely connecting the tractor's battery cables.

Moving Product Off Skid

Details the process of safely removing the tractor from its shipping skid.

Post-Assembly Checks

Lists essential checks to perform after assembly to ensure safe and correct operation.

Operation: Starting the Engine

Pre-Start Checks

Essential checks to perform before starting the engine, including oil and fuel levels.

Starting a Warm Engine

Instructions for starting the engine when it is already warm.

Starting a Cold Engine

Instructions for starting the engine when it is cold.

Engine Starting and Deck Settings

Cold Engine Start Refinements

Refines cold start procedures, especially in low temperatures, and emphasizes warming the engine.

Jump-Starting Procedure

Provides instructions and warnings for jump-starting the tractor with another vehicle's battery.

Setting Cutting Deck Position

Explains how to set the cutting deck to transport or mow position.

Driving and Stopping the Tractor

Forward and Rearward Movement

Details how to control the tractor's direction and speed using the drive pedals.

Cruise Control Usage

Explains how to engage and disengage cruise control for consistent forward speed.

Stopping the Product

Outlines the procedure for safely stopping the tractor, including brake and ignition actions.

Controls and Adjustments

Throttle and Choke Control

Describes how to use the throttle for engine speed and the choke for cold starts.

Headlight Operation

Instructions on how to turn the headlights on and off.

Differential Lock Engagement

Explains how to engage and disengage the differential lock for improved traction.

Cutting Deck and Reverse Operation

Engaging/Disengaging Cutting Deck

Details the procedure for activating and deactivating the cutting deck using the PTO button.

Reverse Operation System (ROS)

Explains the Reverse Operation System (ROS) and how to enable it for mowing in reverse.

Freewheel Mode Engagement

Instructions on how to put the product into freewheel mode for towing or manual movement.

Maintenance Introduction

Maintenance Safety Warning

Provides a crucial safety warning to read and understand before performing any maintenance tasks.

Product Maintenance Schedule

Before Each Use Checks

Lists maintenance tasks to perform before every use of the product.

8-Hour Interval Checks

Outlines maintenance tasks to be performed at 8-hour intervals of operation.

25-Hour Interval Checks

Details maintenance tasks to be performed at 25-hour intervals of operation.

50-Hour Interval Checks

Lists maintenance tasks to be performed at 50-hour intervals of operation.

100-Hour Interval Checks

Outlines maintenance tasks to be performed at 100-hour intervals of operation.

Seasonal and Storage Checks

Specifies maintenance tasks for each season and before storing the product.

Engine Maintenance Schedule

Engine Checks and Intervals

Lists regular engine checks, maintenance intervals, and lubrication guidelines.

Engine Maintenance Tasks

Details specific engine maintenance tasks like filter replacement and cleaning.

Lubrication Schedule

Provides specific guidelines and cautions for lubricating pivot points and bearings.

Cleaning the Tractor

General Cleaning Precautions

Advises against using garden hoses or pressure washers, and recommends compressed air for cleaning.

Deck Washout Port Usage

Instructions on how to use the deck washout port for cleaning the cutting deck after operation.

Adjustments and Tire Checks

Throttle/Choke Cable Adjustment

Information on adjusting throttle and choke control cables if necessary, referring to engine manual.

Tire Inspection and Repair

Guides on checking tire pressure, avoiding damage, and basic tire repair procedures.

V-Belt Examination

Instructions for inspecting V-belts for wear and tear and when to replace them.

Engine Components and Belt Replacement

Transaxle Cooling Fan Maintenance

Advises on cleaning the transaxle cooling fan and fins for engine cooling.

Motion Drive Belt Replacement

Step-by-step guide for removing and installing the motion drive belt, including safety notes.

Battery Servicing

Cleaning Battery Terminals

Provides instructions for cleaning battery terminals to prevent corrosion and ensure proper function.

Replacing the Battery

Details the procedure for safely removing and installing a new battery, including safety warnings.

Connecting Jumper Cables

Explains how to safely connect jumper cables for starting the engine, with critical warnings.

Cutting Deck Procedures

Removing the Cutting Deck

Step-by-step instructions for safely removing the cutting deck from the tractor.

Installing the Cutting Deck

Step-by-step instructions for safely installing the cutting deck onto the tractor.

Cutting Deck Adjustments

Installing Anti-Sway Bar

Instructions for installing the anti-sway bar to stabilize the cutting deck.

Visual Side-to-Side Deck Adjustment

Guides on how to visually adjust the cutting deck for level side-to-side cutting.

Precision Side-to-Side Deck Adjustment

Detailed steps for precise side-to-side adjustment of the cutting deck for optimal results.

Cutting Deck Adjustments and Blade Replacement

Front-to-Rear Cutting Deck Adjustment

Provides instructions for adjusting the cutting deck to ensure proper front-to-rear levelness.

Replacing Cutting Deck Blades

Step-by-step guide on how to safely replace dull, bent, or damaged cutting deck blades.

Drive Belt Maintenance

Removing Cutting Deck Drive Belt

Instructions for safely removing the drive belt from the cutting deck assembly.

Installing Cutting Deck Drive Belt

Guides on correctly installing the drive belt onto the cutting deck pulleys and tensioners.

Engine Maintenance

Engine Lubrication Guide

Details the correct oil type, viscosity, and lubrication procedures for the engine.

Engine Oil Level Check

Instructions on how to check the engine oil level and when to add oil.

Adjusting Anti-Scalp Rollers

Explains how to adjust the anti-scalp rollers on the cutting deck for proper ground clearance.

Engine Oil Replacement

Removing the Lower Cover

Steps to remove the lower engine cover for access to the oil drain valve.

Replacing Engine Oil

Detailed instructions for draining old engine oil and filling with new oil.

Engine Filter and Cooling System Maintenance

Engine Oil Filter Replacement

Guides on how to remove and install a new engine oil filter.

Air Filter and Screen Cleaning

Instructions for cleaning the air filter and air screen to ensure proper engine performance.

Engine Cooling System Maintenance

Advises on keeping the engine cooling system clean to prevent overheating.

Muffler and Spark Plug Checks

Guidance on checking the muffler and replacing spark plugs for optimal engine operation.

Troubleshooting: Engine Start Issues

Engine Not Starting

Lists common causes and actions for when the engine fails to start.

Troubleshooting: Engine Performance

Starter Motor Issues

Addresses problems with the starter motor not turning the engine over.

Engine Running Roughly

Provides solutions for common causes of the engine running unevenly or poorly.

Troubleshooting: Engine Overheating and Power Loss

Engine Overheating Causes

Identifies reasons for the engine becoming too hot and how to resolve them.

Loss of Power Issues

Explains causes for reduced engine power and corrective actions.

Product Vibration Issues

Addresses causes of excessive vibration in the product and how to fix them.

Troubleshooting: Battery and Blade Issues

Battery Charging Problems

Covers issues related to the battery not charging and their solutions.

Operator Presence Control (OPC) Issues

Discusses problems with the operator presence control (OPC) system.

Blade Rotation Problems

Addresses issues preventing the cutting deck blades from rotating correctly.

Defective Grass Discharge

Solutions for problems related to poor grass discharge or cutting results.

Troubleshooting: Movement and Cutting Quality

Headlight Functionality

Troubleshooting steps for when the headlights are not working.

Slow or Irregular Movement

Solutions for the product moving slowly, irregularly, or not at all.

Unsatisfactory Cutting Result

Common causes and fixes for poor grass cutting quality.

Engine Stops on Reverse

Explains why the engine stops when trying to reverse and how to enable ROS.

Transportation, Storage, and Disposal

Safe Transportation Practices

Guidelines for safely transporting the product, including securing it and using appropriate equipment.

Storage Preparation

Steps to prepare the product for long-term storage, focusing on fuel and battery care.

Disposal Information

Advice on the proper disposal of chemicals and worn-out product parts.

Technical Data: Engine and Fuel

Engine Specifications

Provides detailed specifications for the engine, including brand, model, and output.

Fuel and Oil Specifications

Lists fuel requirements, oil types, and volumes for engine operation and maintenance.

Technical Data: Specifications and Service

Tractor Specifications

Details technical specifications for the tractor, cutting deck, tires, and electrical system.

Service Recommendations

Advises on yearly checks at an authorized service center and using genuine spare parts.

Slope Operation Guide

Slope Measurement Guide

Provides a method for measuring slopes to ensure safe operation within the 15-degree limit.

Slope Operation Warnings

Crucial warnings about operating on slopes, emphasizing up/down movement and gradual turns.

Related product manuals

Husqvarna TS 354XD 2022 User Manual

Table of Contents

Questions and Answers:

Husqvarna TS 354XD 2022 Specifications

Summary

Introduction to the Lawn Tractor

Pre-delivery Inspection and Product Numbers

Product Description and Accessories

Intended Use Guidelines

Support and Assistance

Product Overview and Controls

Control Identification

Product Symbols

Operator Symbols and Indicators

Function Indicators

Hazard Indicators

Safety Information

Hazard Symbol Explanations

Product Liability Statement

Emissions Compliance

Safety Definitions

Safe Operation Practices

Child Safety Warnings

General Operation Safety

Safe Operation Practices (Continued)

Personal Protective Equipment (PPE)

Safety Device Checks

Operation Safety Guidelines

Muffler Safety Precautions

Safe Slope Operation

Parking Brake Functionality

Fuel and Battery Safety

Fuel Handling Safety

Battery Handling Safety

Assembly Procedures

Removing Product from Carton

Required Assembly Tools

Loose Parts Identification

Seat Installation and Adjustment

Installing the Seat

Adjusting Seat Position

Adjusting Seat Height

Battery Connection and Pre-Operation Checks

Connecting the Battery

Moving Product Off Skid

Post-Assembly Checks

Operation: Starting the Engine

Pre-Start Checks

Starting a Warm Engine

Starting a Cold Engine

Engine Starting and Deck Settings

Cold Engine Start Refinements

Jump-Starting Procedure

Setting Cutting Deck Position

Driving and Stopping the Tractor

Forward and Rearward Movement

Cruise Control Usage

Stopping the Product

Controls and Adjustments

Throttle and Choke Control

Headlight Operation

Differential Lock Engagement

Cutting Deck and Reverse Operation

Engaging/Disengaging Cutting Deck

Reverse Operation System (ROS)

Freewheel Mode Engagement

Maintenance Introduction

Maintenance Safety Warning

Product Maintenance Schedule

Before Each Use Checks

8-Hour Interval Checks

25-Hour Interval Checks

50-Hour Interval Checks

100-Hour Interval Checks

Seasonal and Storage Checks

Engine Maintenance Schedule

Engine Checks and Intervals

Engine Maintenance Tasks

Lubrication Schedule

Cleaning the Tractor