Hydro AutoDose 1170 - User Manual

10094778 Rev B 11/10 © Hydro Systems Company, Inc. 2010 HydroSystemsCo.com Toll Free: 1.800.543.7184 1
This guide contains instructions for installing, programming, and troubleshooting
the AutoDose™ Dispensing System. Throughout the guide, the following icons are
used to indicate the model(s) to which each step pertains.
AutoDose
™
Automatic Dispensing System
The AutoDose
TM
is a battery or A/C-powered peristaltic pumping dispenser that runs automatically at preset times as
programmed with an electronic timer / control. Product operates reliably and consistantly, even in demanding environments.
!
Please use this equipment carefully and
observe all warnings and cautions.
ALWAYS observe safety and handling instructions of
the chemical manufacturers.
ALWAYS direct discharge away from you or other
persons or into approved containers.
ALWAYS dispense cleaners and chemicals in accordance
with manufacturer’s instructions. Exercise CAUTION
when maintaining your equipment.
KEEP equipment clean for proper operation.
WEAR protective clothing and eyewear when working
in the vicinity of all chemicals, filling or emptying
equipment, or changing tubes.
ALWAYS re-assemble equipment according to
instruction procedures. Be sure all components are
firmly screwed or latched into position. Ensure that
hoses and electrical wires are properly placed and not
kinked or pinched.
ONLY USE ALKALINE BATTERIES.
Tube life will vary depending on the type of treatment
product used. To prevent emergency service, schedule
replacement at least once per year.
NOTE: The batteries should be scheduled for periodic
replacement. Using a total of 40 running (pumping)
hours, create a schedule for servicing the unit and
changing the batteries. Maintaining the power source
as such will help to provide the proper dosing by
providing a more consistent pumping rate.

Models:
Mounts:
Power:
Pail Mount
(3.5 – 5 gal pail)
8 D-cell batteries
Wall Mount
8 D-cell batteries
Wall Mount
A/C Power or 8 D-cell batteries
1170
1180
1190
AutoDose™ Dispenser Specifications:
PUMP
Flow Rate Approx 3.5 oz / min
Tube Material EPDM
Inlet Vacuum 20+ in Hg
Outlet Pressure 20 psi
SYSTEM CABINET
Material Polypropylene and ABS
Size (Model 1170) Approx. 7 3/4” tall X 14” diameter
(does not include container 1170 model system sits on)
Size (Models 1180 and 1190) 4 3/4” X 6 3/4” X 8 1/3”
PROGRAMMABLE TIMER / CONTROL
Program Duration Daily / Weekend / Week Days/Special
Maximum # of Events 24
Dispense Amount per Event 1 oz – 30 oz (dispensed in 1 oz increments)
or 30 – 900 ml (dispensed in 30 ml increments)
This package should contain:
• One AutoDose
TM
dispenser
INSTALL PACKAGE CONTAINING:
• Ceramic weight and strainer for inlet tubing
• Polyethylene tubing (10 ft)
• Cable ties
• Mounting Bracket (Some Models)
• AC Adapter (Some Models)
• Injection Fitting

Summary

AutoDose Dispenser Specifications

General Safety and Handling Warnings

Essential safety precautions for operating the dispensing system and handling chemicals.

Installation Guide

Install the Batteries

Step-by-step instructions for inserting D-cell batteries into the dispenser unit.

Mount the Dispenser

Guidelines for securely mounting the dispenser unit on a wall or surface.

Installation: Power and Location

Install the Power Cord

Instructions for connecting the AC adapter for models that require it.

Determine Dispenser Location

Guidance on selecting the optimal placement for the dispensing unit.

Installation: Tubing and Priming

Install Inlet and Discharge Tubing

Procedures for connecting the tubing for product intake and dispensing.

Prepare and Prime the Dispenser

Steps to prepare the dispenser for use by priming the pump.

User Interface Definition

LCD Display and Control Buttons

Explanation of the user interface, buttons, and indicators on the device.

Device Operation: Access and Time Setup

Unlocking the Device

Procedures for accessing the device's programming mode by entering a PIN.

Setting Time and Day

Instructions for configuring the current time and day on the dispenser.

Device Programming: Dispense Setup

Program Dispense Units and Days

Setting dispense volume units (oz/ml) and selecting days for operation.

Device Programming: Timing and PIN

Program Dispense Times and User PIN

Configuring dispense times and setting a user PIN for security.

Maintenance: Changing Pump Tubing

Replacing the Squeeze Tube Assembly

Detailed steps for removing old and installing new pump tubing.

Troubleshooting and Replacement Parts

Troubleshooting Common Issues

Solutions for problems like the unit not pumping or pumping improperly.

Order Replacement Parts

List of available part numbers for maintenance and repair needs.

Hydro AutoDose 1170 Specifications

General

Brand	Hydro
Model	AutoDose 1170
Category	Dispenser
Language	English