Hytera TETRA PT580H F5 User Manual (English)

Questions and Answers:

E
Erika BrownAug 14, 2025
What to do if Hytera TETRA PT580H F5 network registration fails?
- D
  Dalton ToddAug 14, 2025
  If your Hytera Touch terminal fails to register on the network or cannot find a network, there are a few potential causes. First, ensure the terminal is not operating in DMO mode; switch to TMO mode. Second, check the signal strength to ensure the terminal is within network coverage. Finally, the terminal might not be authorized for network access, in which case you should contact the network operator for authorization.
T
Tricia RamirezAug 17, 2025
Why does my Hytera TETRA PT580H F5 disconnect during calls?
- M
  Michael BlanchardAug 18, 2025
  Abnormal disconnections during a call on your Hytera Touch terminal can occur due to a couple of reasons. The first is that the terminal gets out of the network coverage (in TMO), so check the signal strength and ensure you are within the network coverage. The second is that the terminal operates at an unfavorable position where communication may be blocked by high buildings or frustrated in the underground areas (in DMO), so move to an open and flat area, and restart the terminal.
K
katherine37Aug 21, 2025
Why calls cannot be initiated on Hytera TETRA PT580H F5 Touch terminals?
- C
  Christopher SchwartzAug 21, 2025
  If you're unable to initiate calls on your Hytera Touch terminal, it could be due to a couple of reasons. Ensure that both your terminal and the party you're calling are within network coverage by checking the signal strength. Also, verify that your terminal is operating in the correct mode.
J
Joseph ManningAug 26, 2025
How to fix Hytera Touch terminals that won't power on?
- C
  chaseconnieAug 26, 2025
  If your Hytera Touch terminal won't power on, it's likely because the battery power is too low. Charge the battery.
E
Earl McgrathAug 28, 2025
What to do if a group call can not be initiated on Hytera Touch terminals?
- I
  Ian Wiley MDAug 28, 2025
  If a group call cannot be initiated or received on your Hytera Touch terminal, verify that the terminal is a member of the group. If it is not, contact your dealer to add the terminal to the group. Also, ensure that the terminal is authorized to access the target group by contacting the network operator for authorization.
P
parkerharrySep 1, 2025
Why are Hytera Touch terminals calls always interrupted?
- J
  Julia HunterSep 1, 2025
  If calls on your Hytera Touch terminal are consistently interrupted, it's likely because the current channel is assigned to emergency calls or other calls with higher priority. Wait until the channel becomes available and try again.
B
Brandon HillSep 5, 2025
What to do if a half-duplex call can not be established on Hytera TETRA PT580H F5?
- D
  Dustin SaundersSep 5, 2025
  If a half-duplex call cannot be established on your Hytera Touch terminal, ensure that the call is established within the predefined time period.
Z
zrussellSep 9, 2025
Why is status message content different between sending and receiving parties on Hytera Touch terminals?
- R
  Robert Valencia DDSSep 9, 2025
  If the content displayed for the same status message ID differs between the sending and receiving parties on your Hytera Touch terminal, it's because the parties have associated the same status message ID with different contents. Ensure that the status message ID is associated with the same content.

Hytera TETRA PT580H F5 Specifications

General

Frequency Band	380-430 MHz
Display	2.4" QVGA TFT LCD, 320x240 pixels
Protection Class	IP67
Operating Temperature	-20°C to +55°C
Dimensions	125 x 55 x 37mm
Weight	Approx. 290g (with battery & antenna)
Frequency Range	380-430 MHz
IP Rating	IP67
RF Power	1W