Hyundai HK1207TVE - User Manual

Questions and Answers

M
Maria LaraAug 12, 2025
Why is my Hyundai HK1207TVE not filling up with water?
- T
  Timothy GilmoreAug 13, 2025
  Several reasons may explain why your Hyundai Washer isn't filling with water: * The water tap might not be turned on. In this case, turn on the water tap (it will show E5). * The water pressure might be too low (less than 0.03M Pa). Check and increase the water pressure. * The inlet hose could be kinked. Inspect the inlet hose for kinks. * There might be a water supply failure. Check for a water supply failure. * The program dial might not be properly set. Set the program dial correctly. * The door might not be properly closed. Ensure the door is properly closed. * The inlet hose filter might be blocked. Clean the inlet hose filter.
M
Megan CohenAug 16, 2025
What to do if my Hyundai HK1207TVE Washer fails to operate?
- T
  Timothy WoodardAug 16, 2025
  If your Hyundai Washer fails to operate, consider the following: * Check the connection to the power supply; a poor connection could be the cause. * Check for a power failure. * Ensure the door is properly closed (it will show E1 if not). * Make sure the machine is switched on.
C
Christopher CooperAug 20, 2025
Why is my Hyundai Washer vibrating so much during spin drying?
- J
  Jacob ObrienAug 20, 2025
  Strong vibration during spin drying of your Hyundai Washer can be attributed to a few reasons: * Not all packing bolts have been removed. Make sure to remove all packing bolts. * The washing machine is located on an uneven surface. Level the washing machine. * The machine load is over 7kg. Reduce the machine load. * Not all foam packing has been removed from the motor. Ensure all foam packing has been removed from the motor.
K
katherinemartinezAug 25, 2025
What to do if my Hyundai Washer is draining while filling?
- E
  Emily WeeksAug 25, 2025
  If your Hyundai Washer is draining while also being filled, it could be due to: * The height of the drainage hose being below 80cm. Adjust the drainage hose height to be within 80-100cm. * The drainage hose end being in water. Ensure that the drainage hose end is not in water.
J
John HolderAug 28, 2025
How to fix drainage failure in my Hyundai HK1207TVE?
- L
  Lisa SmithAug 28, 2025
  Drainage failure in your Hyundai Washer can occur due to: * A blocked drainage hose. Clear the blockage in the drainage hose (it will show E2). * The drainage hose end exceeding 100cm above the floor level. Adjust the drainage hose height to be below 100cm. * A blocked filter. Clean the filter.
W
wesleychaseAug 31, 2025
Why does my Hyundai HK1207TVE operation stop before the wash cycle completes?
- A
  Amber YangAug 31, 2025
  If your Hyundai Washer's operation stops before completion of a wash cycle, it might be due to: * Water or electricity failure. Check for water or electricity failure. * The washing machine being in a soak cycle. Wait for the soak cycle to complete.
B
Brian MorrisSep 4, 2025
What causes excessive foam in my Hyundai HK1207TVE?
- K
  Karen EvansSep 4, 2025
  Excessive foam in the drum of your Hyundai Washer, which spills to the distribution drawer, can be caused by: * Using a detergent that is not low-foaming or is intended for manual wash. Use low-foaming detergent or detergent suitable for machine wash. * Using too much detergent. Reduce the amount of detergent used.
C
Christian CunninghamSep 7, 2025
Why does my Hyundai HK1207TVE Washer operation stop for a period of time?
- S
  Sabrina GreenSep 8, 2025
  Your Hyundai Washer might stop for a period of time if: * The washing machine is in a soak cycle. Wait for the soak cycle to complete. * The washing machine gives an error message. Refer to the error message for troubleshooting.