Ickle Bubba CIRRUS - User Manual

Need help?

Do you have a question about the Ickle Bubba CIRRUS and is the answer not in the manual?

Overview

Function Description
Key Components and Features (Car Seat)
Key Components and Features (ISOFIX Base)
Important Technical Specifications
Usage Features
Maintenance Features
Warranty Information

The Ickle Bubba Cirrus i-Size car seat with ISOFIX base is an enhanced child restraint system designed for infants from 40-87cm in height (birth to approximately 15 months) and weighing up to 13kg. It is approved according to UN Regulation No. 129-03 EU i-Size standard. This car seat is specifically designed for rearward-facing installation in i-Size compatible vehicle seating positions, as indicated by vehicle manufacturers in their user manuals. For proper installation and safety, it must be used with an ISOFIX base and support leg.

Function Description:

The Cirrus car seat is designed to provide a safe and secure environment for infants during car travel. It features a multi-position handle, adjustable headrest, and a five-point harness system to ensure the child is properly restrained. The ISOFIX base simplifies installation and provides a stable connection to the vehicle's ISOFIX anchorage points. The car seat can be easily attached to and detached from the ISOFIX base.

Key Components and Features (Car Seat):

Handle: The handle can be rotated into four positions:
- Rearward installation in the car.
- Carrying position.
- Cradle mode.
- Down to support the baby for feeding and play. To rotate the handle, simultaneously press the handle rotation buttons on both sides. Ensure the handle is locked in position before carrying the car seat.
Adjustable Headrest: The headrest can be adjusted to the child's height. To adjust, pull the harness adjuster strap and press the headrest adjuster button. The shoulder harness straps should be at the correct height, level with the child's shoulders.
Belt Guides: These guides ensure the proper routing of the vehicle's seat belt when installing the car seat without the ISOFIX base (if applicable, though the i-Size product requires the ISOFIX base).
Harness Adjuster Strap: Used to tighten or loosen the five-point harness for a snug fit.
Press Adjust Button: This button, often located at the front of the seat, is used in conjunction with the harness adjuster strap to adjust the harness length.
Canopy: Provides shade and protection for the child. It is fitted around the handle and secured with fastenings. The elasticated edge of the hood should be positioned behind the headrest.
Harness: A five-point harness system consisting of shoulder straps, a waist belt, and a crotch strap, designed to securely restrain the child.
Handle Adjustment Button: Buttons on both sides of the handle that allow for rotation and adjustment of the handle's position.
Side Protector: Integrated side impact protection to enhance safety in the event of a side collision.
Harness Adjustment Slots: Multiple slots in the backrest allow for adjusting the height of the shoulder harness to accommodate the child's growth.
Seat Unit: The main body of the car seat where the child sits.
Headrest Height Adjuster: Mechanism for raising or lowering the headrest and shoulder harness simultaneously.
Diagonal Seatbelt Guide: Guides for the diagonal part of the vehicle's seat belt (if used for installation without the ISOFIX base, though the i-Size product requires the ISOFIX base).
Harness Pad: Padded covers for the shoulder harness straps for comfort.
Three-Point Safety Buckle: The central buckle where the harness straps connect.
Crotch Pad: Padding for the crotch strap for comfort.
Newborn Insert (40-75cm): An additional cushion for newborns and smaller infants (40-75cm) to provide better support and a snug fit. This insert must be used for children within this height range.

Key Components and Features (ISOFIX Base):

ISOFIX Connector: Connects the base to the vehicle's ISOFIX anchorage points.
Length Adjustment Button: Used to extend or retract the ISOFIX connectors.
Seat Anchor Point: The point where the car seat attaches to the base.
Release Button: Used to detach the car seat from the base.
Support Leg Length Adjustment Button: Allows for adjusting the length of the support leg.
Support Leg: Provides additional stability and prevents rotation of the car seat in the event of a collision. It must rest firmly on the vehicle floor.
Length Adjustment Indicator: Shows the current length setting of the support leg.
ISOFIX Guide Sleeve: Guides that assist in inserting the ISOFIX connectors into the vehicle's anchorage points.
ISOFIX Click Indicator: Visual indicators (red/green) that confirm correct ISOFIX installation.

Important Technical Specifications:

Standard: R129-03 EU i-Size standard.
Child Height: 40-87cm.
Child Weight: ≤13kg.
Age Range: Birth to approximately 15 months.
Installation: Rearward-facing only, using ISOFIX base with support leg.
Vehicle Compatibility: i-Size compatible seating positions as per vehicle manufacturer's manual.
Airbag Warning: DO NOT use in seating positions with an active frontal airbag.
Harness: 5-point harness system.

Usage Features:

Installation of Infant Carrier on ISOFIX Base:
1. Insert ISOFIX guides into the vehicle's anchorage points.
2. Place the ISOFIX base on the vehicle seat, with the ISOFIX leg pointing towards the floor.
3. Unfold and extend the support leg until it locks. Press the adjustment button and extend the lower section until it rests firmly on the vehicle floor. The support leg indicator must be fully green.
4. Press and push the ISOFIX release buttons on both sides of the base to fully extend the ISOFIX connectors. The ISOFIX indicators will show red.
5. Push the ISOFIX connectors into the vehicle's anchorage points until an audible "click" is heard and the ISOFIX indicators turn green.
6. Push the backrest of the base firmly against the vehicle seat backrest.
7. Shake the enhanced child seat to ensure it is securely fastened and check that all safety buttons and indicators are fully green.
8. To retract the support leg, reverse the procedure: push the leg backward to the base and release the rotation handle.
9. Place the car seat onto the ISOFIX base, ensuring it clicks into place. The indicator on the base should turn green.
Releasing the Infant Carrier from the Base:
1. Pull the seat release handle (located on the base) and lift the car seat using its carry handle.
Adjusting the Carry Handle:
1. Press the handle rotation buttons on both sides simultaneously to rotate the handle to the desired position (rearward installation, carrying, cradle, or feeding/play support). Ensure it locks into place.
Fitting the Hood:
1. Place the hood around the handle and secure it with fastenings.
2. Pull the elasticated edge of the hood behind the headrest.
Usage of Inner Cushion:
1. The inner cushion must be used for children with a height of 40-75cm.
2. Place the inner cushion in the infant carrier.
3. Guide the shoulder straps through the upper and lower parts of the inner cushion.
4. Guide the Y-shaped belt buckle and crotch pad through the openings in the bottom of the inner cushion.
5. Ensure the child is properly secured. To remove, reverse the steps.
Securing the Baby with the Y-shaped Belt:
1. Adjust the shoulder straps and headrest height, and place the inner cushion (if applicable).
2. Press the red button on the buckle, open the buckle, and place the child in the carrier. Place both shoulder straps over the child's shoulders.
3. Bring the two buckle tongues together and insert them into the buckle until they click.
4. Check that the Y-shaped belt is locked by pulling the shoulder straps upwards.
5. To release the child, reverse the steps.

Maintenance Features:

Washing Instructions:
- Plastic Car Seat Shell: Clean with soap and lukewarm water. Do not use abrasive detergents.
- Soft Covers: Hand wash with gentle detergent in warm water. Do not tumble dry.
- Buckle: Clean by rinsing or soaking in lukewarm water to remove blockages. DO NOT use soap or lubricate the buckle or its components.
General Care:
- Replace the infant carrier if it has been subjected to violent stresses in an accident.
- Always secure the infant carrier in the vehicle, even if no child is present.
- Ensure lap straps are worn low on the pelvis.
- Secure all luggage or objects that could cause injury in a collision.
- Ensure rigid and plastic parts are positioned to prevent them from being trapped by a movable seat or vehicle door.
- Always fasten the child to prevent falls.
- Do not alter or add to the device without approval from the competent authority.
- Do not use the infant carrier without its cover.
- Only use manufacturer-recommended seat covers.
- Remove the baby from the carrier before adjusting any movable parts.
- Keep the carrier away from direct sunlight if not equipped with textile, to prevent overheating.
- Never use a second-hand product.
- Regularly check and clean the buckle for dirt.
- Instruct children not to play with the harness buckle.
- No infant carrier guarantees total protection, but correct use reduces the risk of serious injury or death.
- Consult the vehicle manufacturer's handbook before installing this Universal Belted ECRS.

Warranty Information:

Standard Warranty: 2 years* from the date of purchase for pram/pushchair/stroller chassis & frames, and car seats. 1 year for wheels and brake bars. 6 months for all fabric parts, handle coverings, bumper bars, and accessories.
Extended Warranty: Registering the product online within 28 days of receipt extends the standard warranty to 4 years* for applicable parts/items at no extra cost.
Coverage: Manufacturing defects.
Exclusions: Normal wear and tear, incorrect use/storage, damage from not following the user guide, modifications, accidental damage (including airline damage), non-domestic use, or use of non-recommended accessories.
Service: 4-step aftercare service within 5 working days for manufacturing defects under warranty.
Conditions: Warranty applies only in the country of purchase, to the original purchaser, and is non-transferable. It does not cover second-hand purchases.
Registration: Register online at the respective regional website (e.g., https://icklebubba.com/pages/warranty for UK).