r-·
f·-
t ·
,·
I
l
[·
i
r
\.
f
\ _
[_
\._
1--
[_
l:
(D !INPUT SELECT! Switch
Use the [A] and [!J switches to switch the input
signal
as indica ted below.
Since the input channels ( composite signal input CH
A, B, C and A/B,and AUX signal input CH A and
B) operate automatically linked to the !SYNC
EXT!
switch, th ere is no need to operate the !SYNC EXT !
switch every time you switch the channel.
(a) When composite video signals are selected
[ CH A .--.. CH B _. CH C (Y/C) +--+ CH A/ B =1
· When CH C (Y / C) is selected, to select the optional
Y / C input (special function modul e SF301), use
Menu Item 3 (See 5-6.(5)) toselect
Y /C input.
· Th e CH A/ B split splits the screen into top and
bott om so you
can monitor the CH A and CH B
composite signals simultaneou sly (CH A on top and
CH B on bottom). You can
easily adjust the color,
adjus t the white balanc e, and check the video phase
for two cameras and two types of video signals. You
can change the screen split position and which sync
signal to use with ther met hod in 5-6.(2).
(b) When AUX signa l selected (
IAUXI switch is "ON")
· As a sta ndard, one input is equipped. Only CH A
can be selected.
· When opt ional dual component board (DC301) is
installed , switches as indicated below.
(c) When DIGITAL signal selected
~DIGITAL! switch is "ON")
· For CH A, the input (serial/para llel) which is set by
Menu in 5-6 is monitored and for CH B, the serial
input is monitored.
® !AUXI Switch
Wh en this switch is pressed, the LED lights and
signals input to the rear pan el AUX INPUT can be
monitore d. Wh en the switch is pressed a second time
the LED goes out and operation
is changed to the
composit e video chann el.
* Either the RGB signal or YPeP R signal can be input
through the AUX switch. Refer to Section 5-6.(5) for
details of. setting method .
Also, if the optional dual component board is installed,
dual system input is possible. In this case, it
is
possible to switch between AUX A and AUX B using
the !INPUT SELECT ! switch.
@ IDIGITALI Switch
When thi s switch is press ed the LED lights and
signals input through the optionally installed
DIGITAL input, can be monitored. Either DIGITAL
input Dl or D2(or D3) can be installed. Wh en the
switch is pressed a second time, the LED goes out and
operation is switched over to the composite input
chann el.
* There are two types of DIGITAL input,· serial inpu t (2
systems), serial output (1 system: Monitor out) and
parallel input (1 system). With
serial input it is
possible to switch between DIGITAL A and DIGITAL
B
using the !INPUT SELECT! switch.
DIGIT AL A par allel A input
serial A input
Selected by MENU operation.
DIGITAL B serial B input
@ !SYNC EXTI Switch
· When using an external sync signal, set this switch
to "ON". The state of this switch
is store d into the
memories of the input channels. When you set this
switch once, it is switched_ over automat ically. For
example, it is set to
"ON" at CH A and CH C and
to "OFF " at CH B. When you switch the channel to
CH A, B, and C in order with the !INPUT SELECT !
switch, the !SYNC EXTI switch is switched to "ON",
"OFF ", and "ON" in order.
Note) When the DIGITAL input is selected, you can
not operate this switch.
- 15 -
To Next Page
Loading...
