Incra Miter 3000 SE User Manual

Manufactured by Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 ©2016 by Taylor Design Group, Inc. All rights reserved.
Before using the INCRA Miter3000SE, read and follow all of the instructions and safety information in this owner’s manual.
°
When using the INCRA Miter3000SE in conjunction with any other tool, first read and follow all instructions and safety information
in that tool’s owner’s manual.
°
Never let the saw blade come in contact with the aluminum or steel components of the INCRA Miter3000SE.
°
When using the INCRA Miter3000SE, always keep your hands clear of the saw blade and the line of cut.
°
Always turn off the power and make sure that the saw blade comes to a complete stop before changing the setting of any part of the
INCRA Miter3000SE.
°
Always securely tighten the large black clamping knob before starting any cut.
°
Wear safety glasses, hearing protection, and follow all normal shop safety practices.
°
After making any adjustments to the miter angle or fence position of your INCRA Miter3000SE, always verify safe clearance
between the blade and fence before turning on the saw.
°
After making any adjustments to the fence position on the INCRA Miter3000SE, always make sure that the two socket head screws
are securely tightened.
°
When using the INCRA Flip Shop Stop to position a piece for a cut, always hold or otherwise clamp the board between the stop
and the blade.
OWNER’S MANUAL
www.incra.com
Important safety instructions for using the INCRA Miter3000SE
Before using the INCRA
Miter3000SE, read and
follow all of the instructions
and safety information in
this owner’s manual.
by
SAFETY

Incra Miter 3000 SE Specifications

General

Type	Miter Gauge
Fence Length	24 inches
Compatibility	Table saws, band saws, router tables
Angle Range	0-90 degrees
Accuracy	±0.1 degrees
Material	Aluminum
Features	Micro-adjustment, positive stops

Summary

Safety Instructions

Important Safety Instructions

Essential safety precautions for operating the INCRA Miter3000SE.

Assembly and Calibration Guide

Attach Clamping Knob and T-Clip

Instructions for attaching the clamping knob and T-clip to the Miter3000SE.

Adjust Miter Bar Fit

Guide to adjusting the miter bar for a precise fit in the table saw's miter slot.

Attach and Position Fence

Steps for attaching and positioning the fence for safe clearance from the saw blade.

Convert Fence for Right Side Use

Procedure for converting the fence for use in the right-hand miter slot.

Calibrate Fence Mounting Bracket 90°

How to calibrate the fence mounting bracket for a 90° angle to the saw blade.

Calibrate 1/2° Indexing Tooth

Instructions for checking and recalibrating the 1/2° indexing tooth for accuracy.

Operation and Angle Settings

5° Indexing Settings

How to set angles using the 5° indexing mechanism, including common presets.

1/2° Fine Angle Adjustments

Procedure for making fine angle adjustments using the 1/2° indexing system.

Continuous Angle Adjustments

Method for making fine angle adjustments beyond 1/2° increments.

Flip Fence and Shop Stop Features

Zeroing Fence Scales

Steps to zero the main fence scale and extender bar scale for accurate measurements.

Micro Adjust Stop Position

How to make micro adjustments to the Flip Shop Stop position.

Configure Flip Arms and Stop Rods

Explanation of configuring flip arms and stop rods for various cutting configurations.

Make Zero Clearance Sub-Fence

Guide to constructing a wooden sub-fence for improved cutting performance.

Expanded Flip Stop Clamping

How to adjust the Flip Shop Stop for use with thicker wooden sub-fences.

Adjustable Fence Mounting Bracket

How to adjust the fence mounting bracket for precise squareness to the table.