K
Katie AlexanderSep 23, 2025
Why Indel Webasto Marine Ice Maker is still?
- MMichele KimSep 23, 2025
To solve the issue of a still ice maker, check if the stop lever is in the ON position and move the stop lever to the correct position.
To Next PageTo Next PageWhy Indel Webasto Marine Ice Maker is still?
To solve the issue of a still ice maker, check if the stop lever is in the ON position and move the stop lever to the correct position.
What to do if my Indel Webasto Marine Isoterm Drawer Inox compressor runs for a long time but doesn't cool enough?
If the compressor runs for a long time but the Indel Webasto Marine Refrigerator doesn't cool sufficiently, consider these potential causes: insufficient ventilation (improve fan performance), condenser overheating (replace the fan), excessive ice buildup on the condenser (defrost), the door not sealing properly (check door alignment and seal), or a condenser blocked by dust (clean the condenser).
How to troubleshoot Indel Webasto Marine Isoterm Drawer Inox Refrigerator that is not cooling and the compressor won't start?
If your Indel Webasto Marine Refrigerator isn't cooling and the compressor isn't starting, check the following: ensure the electronic control is receiving sufficient power and voltage, and inspect the fuse. Also, verify the battery charger is functioning correctly, and check the thermostat by connecting it to T-C with a separate cable, replacing it if necessary. A defective electronic control could also be the cause.
Why does my Indel Webasto Marine Refrigerator compressor only make short start attempts?
If the compressor makes only short start attempts, it could be due to insufficient voltage or voltage drop triggering the protection device. Check the cables and connections, removing any oxidation or corrosion. Alternatively, the batteries may be flat, so charge them, start the engine, and connect the battery charger.
Why does my Indel Webasto Marine Isoterm Drawer Inox Refrigerator freezer is cold, but the refrigerator is not?
If the freezer is cold but the refrigerator isn't, check for insufficient ventilation, and if ventilation is optimal, have a specialized technician check for gas in the cooling circuit. Also, examine the condition of the electrical connections and the battery for intermittent power supply.
Why does Indel Webasto Marine Ice Maker produce ice with a stale taste?
If the ice has a stale taste, it means the ice is old. You should make new ice.
What does it mean if Indel Webasto Marine Refrigerator makes audible, continuous buzzing?
This sound indicates the water valve is in operation, and no action is required.
What does it mean if Indel Webasto Marine Refrigerator makes audible dripping sound?
This sound indicates water is filling the ice cube making container, and no action is required.
Why Indel Webasto Marine Isoterm Drawer Inox Refrigerator compressor is louder than usual?
If the compressor is louder than usual, check that the compressor screws are tightened well. The compressor may not be well attached to its bracket or is touching the wall.
Why Indel Webasto Marine Isoterm Drawer Inox Refrigerator has excessive ice formation on the evaporator?
Excessive ice formation on the evaporator is caused by moisture entering the refrigerator. Check the condition of the seals on all four sides of the door.
General| Category | Refrigerator |
|---|---|
| Brand | Indel Webasto Marine |
| Type | Drawer Refrigerator |
| Material | Stainless Steel |
| Installation | Built-in |
| Series | Isoterm Drawer Inox Series |
| Capacity | Varies by model (specific model required) |
| Cooling System | Compressor |
| Power Supply | DC |
| Voltage | 12/24V DC |
| Thermostat | Adjustable |
| Refrigerant | R134a |
| Dimensions (HxWxD) | Varies by model (specific model required) |
| Weight | Varies by model (specific model required) |
Product compliance with WEEE directive and proper disposal guidelines.
Warnings regarding R134a refrigerant, product usage, and general hazards.
How to adjust the temperature using the thermostat knob.
Tips for efficient operation, power consumption, and maintenance.
Procedures for defrosting standard and No-Frost Isotherm models.
Instructions for activating and using the DR160 COMBO ice maker.
How the unit protects against low battery voltage.
Recessed installation, positioning, and anchoring requirements.
Step-by-step instructions for installing custom models with front panelling.
Importance of proper ventilation for the compressor/condensing unit.
Procedure for connecting the unit to the vehicle's electrical system.
